One advantage of the combination of Knoppix and Qemu/kvm is that it is not necessary to do any setup of a virtual machine to run Knoppix, and with Knoppix copies on separate partitions bootable with grub, one may simply run gemu/kvm on the MBR of the harddisk and pick the desired install from the ordinary grub boot menu. The actual partition should be mounted read-only at most, as it gets mounted on /mnt-system in the virtual machine.
One complication with qemu/kvm is only simple networking support out of the box: I can reach the internet through the host, default network-manager works just fine for that, but direct communication with the Knoppix guest system isn't set up. Furthermore, with wireless adapters, the traditional simple bridge techique doesn't work.
There are lots of ways to overcome this, and here I want to report just one rather simple, presented in the blog post http://yalb.blogspot.no/2012/04/wire...g-for-kvm.html
It uses the tunctl, from uml-utilities, and parprouted from parprouted
In this case, my internet connection is through a mobile router (192.168.1.1) and wlan0 (192.168.1.100). The guest must be on the same subnet.
I issued the following commands
Then I started qemu/kvm to boot an ordinary Knoppix PMI through grub:Code:sudo sysctl -w /net/ipv4/ip_forward=1 sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 10.10.10.10/32 dev tap0 sudo parprouted wlan0 tap0
In the guest, disable network-manager's networking and setup the virtual eth0, as root:Code:sudo qemu -machine accel=kvm -hda /dev/sda -net nic -net tap,ifname=tap0,script=no -m 1024 &
Somewhat miraculously to me, this worked!Code:ifconfig eth0 192.168.1.99 up # Static IP echo 'nameserver 192.168.1.1' > /etc/resolv.conf # Use the nameserver of the host route add default gw 192.168.1.100 # Host IP
I haven't tried yet, but this should work for at least a few VM's, creating tap1, tap2 etc and using them instead of tap0.
This way, servers can be tested out or routinely run with qemu/kvm just by copying the KNOPPIX directory (to be precise, in this case KNOPPIX705R1, remastering 1 of 7.0.5) to a partition (which may contain just about anything besides), setting up a grub menu entry for the copy and run qemu/kvm.
My practical motivation for this is to run a database server and a web server on separate virtual machines, possibly an application server too. With three extra partitions, I can easily run three VMs simulataneously this way.
I have used VMware Workstation for this earlier, but this approach seems both simpler and more flexible to me. Plus I can spare myself the frequent VMware module compilation blues. (Workstation 8.0.5 works fine with Knoppix 7.0.5, BTW - Workstation 8.0.4 does not.)
DELL PowerEdge R730 Server 2x E5-2690v4 2.6GHz =28 Cores 128GB H730 4xRJ45
$458.00
HP ProLiant DL380 Gen9 8SFF Server - E5-2698 v3 - 32Cores - 128GB Ram - 1TB HDD
$299.00
Dell PowerEdge R330 Xeon E3-1220 v5 3.0GHz 32gb H330 2x 3.5" Trays SVR 2012
$189.99
HP ProLiant DL360 Gen9 Server 2x E5-2620v4 2.1GHz =16 Cores 32GB P440AR 4xRJ45
$220.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell R630 Server 2x E5-2620 V4 2.1GHz =16 Cores 128GB DDR4 1x 960GB 2x 1G 2x 10G
$210.00
HP ProLiant DL360 G9 Server 2x Xeon E5-2690 V3 24 Cores 2.6GHz P440ar 128GB DDR4
$249.99
HPE ProLiant DL380 GEN10 G10 Rack Server - 1X Silver 4208 + 32GB RAM 366FLR
$599.99
DELL PowerEdge R730 Server 2x E5-2697v3 2.6GHz =28 Cores 32GB H730 4xRJ45
$288.00
Dell Poweredge R620 2x E5-2680 2.7ghz 16-Cores / 128gb / H710 / 2x Trays / 750w
$199.99