Add those module names to /etc/modules (or /etc/modules-KERNEL-VERSION if it exists). These modules are loaded at each boot.
Hello,
some weeks ago I had installed Knoppix 3.3 on HDD and everything works fine. But at that time, the USB support was switched off in the BIOS. Thus, there are now as a result no USB modules available in my Knoppix HDD installation (the output of "dmesg" doesn't show anything about a USB driver).
How can I add the needed USB modules (probably usbcore, usb-uhci and usb-storage) to my system?
When I boot Knoppix from CD, my USB stick is at least found within the "K Info Centre" and the vendor name / serial number shown there. Hence, the hardware seems to be working. Yet, I could't mount the USB stick so far as there seem to be some additional filesystem problems.
But what I actually want is to use the USB stick with my existing Knoppix 3.3 HDD installation. What shall I do???
Thanks in advance for your help!
Oli
Add those module names to /etc/modules (or /etc/modules-KERNEL-VERSION if it exists). These modules are loaded at each boot.
Hi Kelmo,
if this was so easy, I'd be glad. But it isn't!
I tried insmod usb*, but it didn't find the usb-storage module. Then I found it somewhere deep in the directory tree and installed it there manually. But when I try to mount my usb stick on sda1, I always get the error message: "not a valid block device". sda4 is my Iomega ZIP drive which works fine.
As I wrote, the situation is a little bit different when booting from CD (Knoppix 3.3 or 3.4ct): Then, the USB stick is recognized correctly (as shown with "dmesg"), but Knoppix installs four SCSI devices, named sda1, 2, 3, and 4. sda4 should be my Iomega ZIP drive. However, if you try to mount any of the sda1...4 devices, you'll get the error message "filesystem could not be detected".
Please help!
Olivier
I believe that it is a problem with the partition table of the device that you are trying to mount. The mere fact that the filesystem is the trouble means that the device is being detected properly.
I cannot give any more info, because I am not 100% certain on how to correct this, but it is a problem with the partition table.
I have read other threads in this forum on the same topic.
WD HDD Ultrastar DC HC520 HUH721212AL4205 12TB 3.5" SAS Server Hard Disk Drive
$45.27
Seagate Exos 7E10 ST2000NM000B 2TB 7200RPM SATA 6.0Gb/s 3.5" Internal Hard Drive
$29.99
WD 16TB Elements Desktop, Certified Refurbished Hard Drive - RWDBWLG0160HBK-NESN
$209.99
Western Digital WD4000FYYZ RE 4TB 7200 RPM 64MB Cache SATA 6Gb/s 3.5" Hard Drive
$28.48
HGST Ultrastar DC HC520 12TB SATA 6Gb 256MB 3.5" Enterprise HDD- HUH721212ALE601
$82.99
HGST Ultrastar HE10 HUH721010ALE600 10TB SATA 6Gb/s 7200RPM 3.5" Enterprise HDD
$78.99
HP 4TB 3.5" 12Gb/s 7.2K SAS Hard Drive P/N: 793674-001 / 803634-001 / 695597-004
$17.49
WD Ultrastar DC HC530 14TB SATA 6G 3.5" 7200RPM Enterprise HDD - WUH721414ALE604
$112.00
Seagate Enterprise Capacity v7 ST12000NM0127 12TB 7.2K RPM SATA 6Gb/s 512e HDD
$40.16
HDD 3.5" SATA Hard Drive with Windows 7/Win 10 Installed Legacy
$35.99