Add those module names to /etc/modules (or /etc/modules-KERNEL-VERSION if it exists). These modules are loaded at each boot.
Hello,
some weeks ago I had installed Knoppix 3.3 on HDD and everything works fine. But at that time, the USB support was switched off in the BIOS. Thus, there are now as a result no USB modules available in my Knoppix HDD installation (the output of "dmesg" doesn't show anything about a USB driver).
How can I add the needed USB modules (probably usbcore, usb-uhci and usb-storage) to my system?
When I boot Knoppix from CD, my USB stick is at least found within the "K Info Centre" and the vendor name / serial number shown there. Hence, the hardware seems to be working. Yet, I could't mount the USB stick so far as there seem to be some additional filesystem problems.
But what I actually want is to use the USB stick with my existing Knoppix 3.3 HDD installation. What shall I do???
Thanks in advance for your help!
Oli
Add those module names to /etc/modules (or /etc/modules-KERNEL-VERSION if it exists). These modules are loaded at each boot.
Hi Kelmo,
if this was so easy, I'd be glad. But it isn't!
I tried insmod usb*, but it didn't find the usb-storage module. Then I found it somewhere deep in the directory tree and installed it there manually. But when I try to mount my usb stick on sda1, I always get the error message: "not a valid block device". sda4 is my Iomega ZIP drive which works fine.
As I wrote, the situation is a little bit different when booting from CD (Knoppix 3.3 or 3.4ct): Then, the USB stick is recognized correctly (as shown with "dmesg"), but Knoppix installs four SCSI devices, named sda1, 2, 3, and 4. sda4 should be my Iomega ZIP drive. However, if you try to mount any of the sda1...4 devices, you'll get the error message "filesystem could not be detected".
Please help!
Olivier
I believe that it is a problem with the partition table of the device that you are trying to mount. The mere fact that the filesystem is the trouble means that the device is being detected properly.
I cannot give any more info, because I am not 100% certain on how to correct this, but it is a problem with the partition table.
I have read other threads in this forum on the same topic.
~CLEARANCE SALE~ 13.3" TouchScreen HP EliteBook: Intel i7 8GB RAM 256GB SSD
$244.99
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$12.90
Team T-FORCE VULCAN Z 32GB (2 x 16GB) PC RAM DDR4 3200 (PC4 25600) Memory
$47.59
Team T-FORCE VULCAN Z 16GB (2 x 8GB) 288-Pin PC RAM DDR4 3200 (PC4 25600) XMP
$34.99
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$21.50
Crucial 16GB (2x 8GB) Kit DDR3L 1600MHz PC3-12800 UDIMM Desktop 240-Pin CL11 RAM
$22.85
Kingston HyperX FURY DDR3 8GB 16GB 32G 1600 1866 1333 Desktop Memory RAM DIMM
$13.25
256GB Kit (8 x 32GB) PC4-17000 LRDIMM DELL POWEREDGE R730xd R730 R630 Memory RAM
$303.92
HyperX FURY DDR4 8GB 16GB 32GB 3200MHz PC4-25600 Desktop RAM Memory DIMM 288pins
$72.93