can you be more specific about setting up hdd (after knoppix-installer + setting up mfs) openmosixviewer
what is "setting up mfs ? mean
thanks
peter
I just recently tried to setup several nodes with clusterKNOPPIX 3.6 CDs and the cheatcode "knoppix toram." If I boot normally from CD (no cheats) or from hdd (after knoppix-installer + setting up mfs) openmosixviewer can see all the nodes and all the migration. If I use toram, I only see the local node, sometimes I see a remote node in red.... Is there a fix for this?
TIA,
AJG
can you be more specific about setting up hdd (after knoppix-installer + setting up mfs) openmosixviewer
what is "setting up mfs ? mean
thanks
peter
Take a look at:
http://www.knoppix.net/forum/viewtop...r+mfs&start=50
Regards,
AJG
for plener: first u make sure ur master node is up and can access the network, then u set up the knoppix openmosix terminal server as stated, then u make sure your client node's network card support pxe boot (u need to enable network boot in your BIOS), then just start ur client node.
and to: el_supremo, A. Jorge Garcia and wangji
I finally found you guys that used quantian successfully, do u mind give me a little hint about my problem?
I may start quantian in my vmware (boot:migshm), and set up the openmosix terminal server successfully, and then my node and PXE boot from it, my openmosixview also found 2 cpus now, however, while i just randomly open some applications to see if the load is being migrated and the other cpu is not showing any load at all.
and I found this error on the other node saying that:
openMosix: Auto-migration of local-processes from this node re-enabled
openMosix: guest-processes now accepted again
MFS already mounted!
omdiscd[2774]: bind failed on interface 0: Address already in use
omdiscd[2774]: Unable to initialize network. Exiting.
any comments are greatly appreciated
I've never gotten PXE to wprk right in my lab.
I recommend all nodes boot a CD or all nodes be hdinstalled. I've recently had more success with a CD only distro (no hdinstall option) that runs on a 200MB CD and, as a rexult, boots about as fast as hdinstall. This distro in BCCD (Bootable Cluster CD) which also uses openMOSIX. Maybe you sould try it!
Regards,
AJG
Thx Jorge:
The reason I used quantian PXE boot my slave nodes is that my slaves don't have DVD ROM, but anyways, I did progress a bit and see the load of the cpu shifting back and forth to different nodes using the IBM test script testapp.c here (thx to a friend who mentioned this in the early post)
http://www-128.ibm.com/developerwork...knop.html#main
I did try BCCD, and it appears not to support my netword card, so...what a pity.
It's real hard for the openmosix to utilize unless u use some big software such as blender or stuff...so openmosix is really got to develop much further.
Keep in touch, thx!
Green label hologram Cisco SFP-10G-LR-S SFP Transceiver Module
$28.00
New Cisco w/ Green Hologram SFP-25G-SR-S 25G SFP28 SR 850nm 300m LC MMF Module
$69.99
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
New Cisco w/ Green Hologram SFP-10G-LR-S 10G SFP+ LR 1310nm 10km SMF LC Module
$34.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Lot of 10 - HP 10Gb SR SFP+ Transceiver 455883-B21 455885-001 456096-001 850nm
$25.99
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$10.99
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00
GENUINE CISCO DS-SFP-FC32G-SW SFP NEW SEALED SEE PHOTOS SHIPS FREE
$69.99