Have you tried this:
modprobe ohci1394
Let us know how it goes eh?
Hi,
I have a Sony Vaio GRX600. I have attached to it via the iLink (1394)port a hard drive inside a drive enclosure. Knoppix recognizes the 4 internal NTFS partitions on the Sony, but does not seem to recognize the external drive which is FAT32.
What can I do to help Knoppix recognize the external drive?
Thx,
tomber
************************
LCPI.txt
¬ \@¬ \@compatible controller: ATI Technologies Inc Radeon Mobility M7 LW
(prog-if 00 [VGA])
Subsystem: Sony Corporation: Unknown device 80fa
Flags: bus master, stepping, fast Back2Back, 66Mhz, medium devsel, latency
66, IRQ 9
Memory at f0000000 (32-bit, prefetchable) [size=128M]
I/O ports at 3000 [size=256]
Memory at e8100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: <available only to root>
02:05.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a
Subsystem: Sony Corporation: Unknown device 80fa
Flags: bus master, medium devsel, latency 168, IRQ 3
Memory at e8202000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
I/O window 0: 00004400-000044ff
I/O window 1: 00004800-000048ff
16-bit legacy interface ports at 0001
02:05.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a
Subsystem: Sony Corporation: Unknown device 80fa
Flags: bus master, medium devsel, latency 168
Memory at e8203000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
I/O window 0: 00004c00-00004cff
I/O window 1: 00000000-00000003
16-bit legacy interface ports at 0001
02:05.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller
(prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 80fa
Flags: bus master, medium devsel, latency 64
Memory at e8201000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <available only to root>
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) Chipset Ethernet
Controller (rev 42)
Subsystem: Sony Corporation: Unknown device 80fa
Flags: bus master, medium devsel, latency 66, IRQ 9
Memory at e8200000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 4000 [size=64]
Capabilities: <available only to root>
Have you tried this:
modprobe ohci1394
Let us know how it goes eh?
It's not working so I am going to get a new copy of Knoppix--one without the cloop errors. I bought this thing of ebay because the isos I download never match in md5 and won't boot. I am going to start over and repost later. Thx.
GENUINE CISCO 25G Base Active Optical SFP cable 3M SFP-25G-AOC3M NEW SHIPS FREE
$65.99
Cisco Meraki MA-SFP-10GB-LR 10G SFP+ LR 1310nm 10km LC SMF
$39.99
Cisco Meraki MA-SFP-10GB-SR 10G SFP+ SR 850nm 300m LC MMF
$29.99
Cisco w/ Green Hologram SFP-10/25G-LR-S 10/25GBASE-LR SFP28 Transceiver Module
$79.99
NEW FS SFP-10G-T 10GBASE T SFP+ 30M Transceiver Module (Lot of 1)
$39.95
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
New Cisco w/ Green Hologram SFP-25G-SR-S 25G SFP28 SR 850nm 300m LC MMF Module
$69.99
New Cisco w/ Green Hologram SFP-10G-LR-S 10G SFP+ LR 1310nm 10km SMF LC Module
$34.99