These may give you some ideas.
http://www.knoppix.net/forum/viewtop...?p=52847#52847
http://www.knoppix.net/forum/viewtop...?p=59980#59980
jd
I have an harddrive with 1.2GB as hda1 formatted as fat32.
I followed the Poor Man's Install and everything is ok.
I created a persistent home as image, i save my config.
Everything is ok, and running with cheatcodes:
knoppix home=scan myconfig=scan fromhd=/dev/hda1
but i'd want to boot from HD and not from CD, but i don't know how to configure the grub or the lilo.
Help me, please.
These may give you some ideas.
http://www.knoppix.net/forum/viewtop...?p=52847#52847
http://www.knoppix.net/forum/viewtop...?p=59980#59980
jd
see this:http://www.knoppix.net/docs/index.ph...HDInstallHowTo
it has tips about installing a toHD system.
To summarize:
use lilo. I'm assuming you have only one partition, hda1 (or hda1 plus a swap).
copy the directory /boot/isolinux from the cd to the hd.
you really only need the files /boot/isolinux/linux24, linux26, minirt24.gz & minirt26.gz.
Then edit /etc/lilo.conf add the following:
If you have another o/s, add it too. a windows entry is usuallyCode:image=/mnt/hda1/boot/isolinux/linux24 label="Knoppix3.4-24" append="lang=us fromhd=/dev/hda1 home=scan myconfig=scan apm=power-off" initrd=/mnt/hda1/boot/isolinux/minirt24.gz read-only image=/mnt/hda1/boot/isolinux/linux26 label="Knoppix3.4-26" append="lang=us fromhd=/dev/hda1 home=scan myconfig=scan apm=power-off" initrd=/mnt/hda1/boot/isolinux/minirt26.gz read-only
run lilo to install lilo to the mbr.Code:other=/dev/hda1 label="Windows" table=/dev/hda
That's it, you should now be able to boot into your Knoppix.
If you are unable to edit /etc/lilo.conf because of the read only file system, copy it to /home/knoppix then run lilo with
lilo -c /home/knoppix/lilo.conf
Oops; sorry I think this should be:
notCode:image=/dev/hda1/boot/isolinux/linux24 and initrd=/dev/hda1/boot/isolinux/minirt24.gz
Code:image=/mnt/hda1/boot/isolinux/linux24 initrd=/mnt/hda1/boot/isolinux/minirt24.gz
Sorry but it's the other way around; eg the mnt entries are the correct ones. Note that hda1 needs to be mounted (eg on its default mount point /mnt/hda1) when running lilo. I advise to always run "lilo -v" and pay attention to the possible error messages.Originally Posted by CrashedAgain
Right. I thought of that also but haven't had time to correct myself yet.Originally Posted by baldyeti
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$12.90
A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G
$13.99
Lot of 2 32GB DDR4 2666 PC4-21300 SODIMM RAM Modules Mixed Brand
$60.00
HyperX FURY RAM DDR4 16GB 8GB 32GB 4GB 3200 2666 2400 2133 Desktop Memory DIMM
$9.64
Samsung 128GB (4x 32GB) M86B4G70DM0-CMA3 PC3-14900L 4Rx4 DDR3 ECC Reg Server Mem
$39.99
Kingston HyperX FURY DDR3 8GB 16GB 32G 1600 1866 1333 Desktop Memory RAM DIMM
$13.25
Samsung 16GB 2Rx4 PC4-2400 RDIMM DDR4-19200 ECC REG Registered Server Memory RAM
$20.99
A-Tech 256GB 4x 64GB 4Rx4 PC4-19200 ECC Load Reduced LRDIMM Server Memory RAM
$287.96
A-Tech 128GB 2x 64GB 4Rx4 PC4-19200 ECC Load Reduced LRDIMM Server Memory RAM
$143.98