-
No Internet - eth0 = ok, pppoe = in use(??) with live cd 3.6
I can't connect to the internet with the live cd 3.6 (DSL).
Since I can't do anything wrong - after affirming having only one eth0 I get the error message with "pppoe already in use" - I guess, it's because of my new chipset (VIA KT880) and the build in LAN.
Can anyone enlighten me?
Except for internet Knoppix runs fine - I can't even get Mandrake 10.1 to install - but believe me or not, sometimes I do need the internet.
If it's my chipset, does it mean, no Linux distribution would work (at the moment?)?
OT: My mainboard has SATA (and RAID), which is deaktivated, and I've heard about problems with SATA and Linux. Do these problems arise even if you don't have any SATA disks but only the (disabled) chipset? Because I need a new disk and if I have problems even with the normal (P-) ATA disks then I might as well buy a SATA disk. (I think my Mandrake problems are due to this.)
Addendum 2004-09-29T19:57
Problem solved
wechsle auf eine konsole. logge dich als root ein.
gib ein:
pppoe
und es erscheinen nach kurzer zeit ein paar seltsame zeichen. dann wieder der prompt.
nun kannst du mit
pppoeconf
die konfiguration starten. nun wird der dsl-concentrator (oder wie das ding heißt) wundersamerweise erkannt.
aus http://www.supportnet.de/discussion/...nicht+gefunden
It seems to be a bug, since I found it in 3.6 and 3.7 but not in 3.2 and 3.3.
-
-
Senior Member
registered user
What does
show?
pppoe is in use?
Did you configure your ISP?
Did you specify the DNS-servers?
Code:
cat /etc/resolv.conf
Does ping work?
(knoppix.net)
-
I didn't have any choice to enable or disable anything!
I'm booting from the live cd and when I see the desktop I try to connect to the internet.
After clicking through the menus the very first message appearing is the one with something like "congratulation, founding eth0 .. if this the only one eth - which it is! - then proceed by clicking "ok". The ok button is already marked with green.
And then, after cklicking the ok button, I get the second message with "sorry, pppoe already in use .. can't do anything".
I DON'T have AT ANY TIME a choice to disable, or enable, or filling out with text, anything.
No, I didn't ping anything; I see on the LED of my DSL modem that I'm not connected.
-
no connection to access concentrator - ARCOR DSL
Addendum "no connection to access concentrator"
I put a Realtek in without success (and tried Knoppix 3.7).
Knoppix found then 2 eth but I still get the same error message. That message is actually the third window, the second one is just showing shortly with "Looking for ..."
And the error message is actually "No access concentrator could be contacted(!) That could be due to pppoe beeing already in use"
Sorry for my wrong wording earlier.
Maybe Knoppix has problems with my Arcor DSL? But that's just a white box without any configuration and which works fine with Win XP.
-
Senior Member
registered user
Have you run netcard config ?
Do your system has firewire?
-
Senior Member
registered user
If you added the 'solved' to the bottom of the thread, I would have found it before writing more hints, and only finding the 'solved' by accidential scrolling in the wrong direction....
Similar Threads
-
By aussiemarine in forum Hdd Install / Debian / Apt
Replies: 4
Last Post: 09-07-2005, 12:36 PM
-
By nlyric in forum General Support
Replies: 0
Last Post: 08-26-2005, 05:57 AM
-
By Maistro in forum General Support
Replies: 1
Last Post: 03-23-2005, 11:03 PM
-
By dylan000 in forum General Support
Replies: 6
Last Post: 09-13-2004, 06:47 PM
-
By voxxell99 in forum Networking
Replies: 0
Last Post: 09-25-2003, 01:08 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Cisco Nexus 48-Port 10G SFP+ Switch N9K-9396PX w/ 9K-M12PQ 12-Port 40G QSFP
$419.99
Cisco GLC-FE-100FX-RGD 100BASE-FX SFP Transceiver Module
$17.99
Lot of 10pcs Brocade 57-1000012-01 8Gbps SWL 850nm SFP+ Optical Transceivers
$19.00
CISCO SFP GLC-GE-100FX 10-2019-02 100Base-FX SFP GBIC Transceiver Module 1pcs
$52.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
Genuine Cisco ‎SFP-10G-SR Transceiver Module (10-2415-03)
$5.85
10 PCS Cisco GLC-LH-SMD 10-2625-01 1310nm SFP Transceiver Module
$85.00
New HP HPE Aruba J9150D 10G SFP+ LC SR 850nm 300m MMF XCVR Transceiver Module
$49.99