Knoppix is 3.7 live cd
There is no modem on the boot screen.
Ray
Hi forum
I have a Creative modem blaster 56k v.92 PCI di5633 HCF modem that I am trying to connect to the internet via kppp and or pppconfig. Modem is on com 3 and is an internal.
I have used all combinations in kppp possible and the only returns I get is modem ready and either modem busy or modem initilizing. Waited on initilizing as long as 30+ minutes no go.
Scanned lspci -v and recieved the following info:
0000:01:0b.0 Communication controller: Conexant HCF 56k data/fax/voice modem (worldwide)(rev0
Subsystem: DIGICOM Systems,Inc: unknown device 1059
Flags: bus master,medium devsel,latency 64,IRQ 9
Memory at ff8f0000 (32-bit,non-prefetechable)(size 64k)
IO Port at dff0 [size=8]
Capacities: [40] power management version 2
Your help will be greatly appreciated
Ray
Knoppix is 3.7 live cd
There is no modem on the boot screen.
Ray
As far as I know, only way to connect to net with Live Knoppix over dial-up modem is to have hardware modem. Unfortunatelly, your modem seems to me like winmodem (HCF). There are some PCI hardware modem. All external, SERIAL (not USB) modems are hardware and work out of the box. kppp can't help you in this situation. If you install Knoppix to hdd, you need driver for your modem and so on. Here is a quote from one post on net:
"The Conexant HCF and HSF winmodems are supported by the Linuxant drivers. This started as free software, but snowballed to the point where the guy decided he should charge a fee for it. The upside is that it's a very highly developed and polished driver. You can download it for free to verify that it works with your modem, but it's limited to 14.4k. $15 gets you the unrestricted 56k version."
And $30 might get you el cheapo external serial modem...................$15 gets you the unrestricted 56k version.
Hey,
i have knoppix3.7 running from live cd,
i was trying to configure my isdn modem, Telstra NT1 Plus II, it is connected via usb.
it shows up on usb view as connected to the usb controller.
being a novice i am not sure how to configure it. I tried the instructions thats come with this modem for instaling it on red hat but they didnt seem to work for me.
Thanks for the information
This confirms the info from linmodem,forums and help sheets
I have just purchased a Suse distro so this info made me decide to purchase
Zoom serial external modem which says it will work with Microsoft,Linux and Mac.
Your help is greatly appreciated
Ray
HPGYT DELL Micron 5100 PRO 960GB SATA 6Gb/s 2.5in SSD 0HPGYT MTFDDAK960TCB Gen14
$69.00
### MZ-7KE1T0 Samsung 850 Pro Series 1TB 2.5 inch SATA3 SSD ###
$105.00
Micron 3.84TB SSD 5200 ECO SATA 2.5" MTFDDAK3T8TDC D1MU420 Solid State Drive
$312.00
Patriot P210 128GB 256GB 512GB 1TB 2TB 2.5" SATA 3 6GB/s Internal SSD PC/MAC Lot
$14.99
Micron 5100 MAX 120GB SATA 6Gb/s 2.5" Internal SSD MTFDDAK120TCC Solid State
$9.89
Netac 1TB 2TB 512GB Internal SSD 2.5'' SATA III 6Gb/s Solid State Drive lot
$13.99
Fanxiang SSD 512GB 1TB 2TB 4TB 2.5'' SSD SATA III Internal Solid State Drive lot
$13.99
M.2 NVMe SSD 128GB 256GB 512GB Single Notch with Windows Installed 10 / 11
$85.25
Fanxiang M.2 SATA SSD 2TB 1TB 512GB 256GB SSD Internal M2 Solid State Drive Lot
$109.99