-
monitor displays nothing when starting knoppix
i've just recently downloaded knoppix, and i burned it onto a cd, hoping i would be able to use it by today. i stick the disk into my drive, wait for my computer to boot up, get the the little "do you want to use knoppix" screen, pressed enter, and......nothing.
when i pressed enter, a little message that said "Out of Range popped up onto my monitor. how can i fix this so that i can view Knoppix?
my monitor is a Microtek 710S
My video card is an SIS 650 (i belieive; its something like that)
i'm using Knoppix 3.9
if there is anymore information i should provide, please ask.
-
Senior Member
registered user
It sounds like knoppix is doing the best it can at autodetecting the video hardware (perhaps getting it wrong) & then setting a resolution & refresh rate that is beyond the capabilities of the hardware. Try booting knoppix with some Cheat Codes, such as:
knoppix screen=800x600 xvrefresh=60
knoppix screen=640x480 xvrefresh=60
I hope this helps.
James
-
thanks for your help, but unfortunately this didnt resolve the problem
the same message is popping up on my monitor.....any other ideas as to what to do?
-
I have the same problem when booting up, the screen resolution & refresh rate is different so during start up the screen become distorted.
I am new to Knoppix, can anyone teach me where to find boot prompt to configure it and save the configuration to the harddisk so the next boot up can start to that setting.
-
should i mention that when the message "Out of Range", its a monitor message, coming from the monitor. Knoppix is not delivering the message.
agh i'm so confused.
-
-
It must be SYNC OUT OF RANGE not Out of range ... I think ur using a very old monitor.
-
Senior Member
registered user
Originally Posted by
indiandude514
should i mention that when the message "Out of Range", its a monitor message, coming from the monitor.
Have a look at the cheatcodes, especially the Tips & Tricks.
If you are unable to book Knoppix, try one or both of these two boot commands:
boot: knoppix vga=0 debug -b 3
...
boot: failsafe debug -b 3
Are you able to get to the final stage? If not, what is the last stage you are able to get to?
Regards,
- Robert
http://www.cwelug.org/
Similar Threads
-
By daviddoria in forum Hardware & Booting
Replies: 7
Last Post: 05-15-2010, 11:42 PM
-
By robwelch100 in forum General Support
Replies: 0
Last Post: 04-02-2005, 02:48 AM
-
By kenelder in forum General Support
Replies: 8
Last Post: 07-12-2004, 06:42 PM
-
By Zer0th in forum General Support
Replies: 0
Last Post: 04-02-2004, 05:01 AM
-
By tommydl in forum Ideas
Replies: 0
Last Post: 03-29-2004, 08:30 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$12.90
Samsung 128GB (4x 32GB) M86B4G70DM0-CMA3 PC3-14900L 4Rx4 DDR3 ECC Reg Server Mem
$39.99
A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G
$13.99
HyperX FURY RAM DDR4 16GB 8GB 32GB 4GB 3200 2666 2400 2133 Desktop Memory DIMM
$9.64
Lot of 2 32GB DDR4 2666 PC4-21300 SODIMM RAM Modules Mixed Brand
$60.00
Samsung 16GB 2Rx4 PC4-2400 RDIMM DDR4-19200 ECC REG Registered Server Memory RAM
$20.99
8GB PC3L-12800S 1600MHz SODIMM DDR3 RAM | Grade A
$12.00
A-Tech 256GB 4x 64GB 4Rx4 PC4-19200 ECC Load Reduced LRDIMM Server Memory RAM
$287.96
A-Tech 128GB 2x 64GB 4Rx4 PC4-19200 ECC Load Reduced LRDIMM Server Memory RAM
$143.98