anyone?
Card: Linksys WUSB54Gv4, 802.11b/g, USB 2.0 -- link here
Chipset: RT2500USB (RT2571F) (They just changed the chip and didn't tell anybody. Be careful which version (v1/v2/v4) you buy!)
usbid: 13b1:000d
Driver 0: Ralink driver: http://www.ralinktech.com/supp-1.htm - 2005-03-25 / Drv2.0.1.0, rt2500usb.inf & rt2500usb.sys
Notes: ndiswrapper v1.2-rc1, kernel 2.6.11.7 (also works with grsec2 patch v2.1.5): works on both USB2.0 (load with modprobe ehci-hcd log2_irq_thresh=4 to avoid "usb X-Y: reset high speed USB device using ehci_hcd and address Z") and USB1.1 (UHCI (OHCI not tested (yet?))). WEP works with 64bit and 128bit keys. but bitrate is only 11Mbit/s Note: rename the configuration file for the adapter once you installed the drivers (getting them extracted is quite a mess (WINE/Cedega) you need rt2500usb.*). 'mv /etc/ndiswrapper/rt2500usb/148F\:2570.0.conf /etc/ndiswrapper/rt2500usb/13b1\:000d.0.conf' should do the trick.
Driver 1: Linksys Windows XP driver: http://www.linksys.com/download/default.asp
Notes: ndiswrapper v1.1, kernel 2.6.11.7 vanilla: kernel-oops!
ndiswrapper v1.2-rc1 loads fine (EHCI loaded with modprobe ehci-hcd log2_irq_thresh=4) but oopses when unloading the module and the adapter is still plugged in (Kernel 2.6.11.7 vanilla). Yet transmission seems to fail completely (except increasing 'Tx Invalid misc' values nothing happens).
Driver 2: older Linksys Windows XP driver: ftp://ftp.linksys.com/pub/network/WU...4_20040703.exe
Notes: ndiswrapper v1.2-rc1, kernel 2.6.11.7 (also works with grsec2 patch v2.1.5): seems to work, but only 11Mbit/s and without any encryption. no need to unplug the device before removing the ndiswrapper module. works on USB2.0, USB1.1 not tested (yet).
Driver 3:There is a native driver for rt2x00 but it has no USB support yet. View its status at rt2x00.serialmonkey.com
i have no idea what that means , i had the cd , and exported the driver to my home folder , and then used ndiswrapper and it said trhat the module was running perfectly but thatr there was no such device , can anyone help me installing it , i have beeen googling for hours and i give up , help please.
anyone?
edit
You are the only one who had posted in the thread so far. You do not indicate that you are quoting anyone else or have copied information from anywhere, but you suddenly, in the middle of a long and detailed post say the above? Do you see how that might confuse others?Originally Posted by johnsmith01
i found that 5 minutes ago sorry , i was doing something else so just posted it
Broadcom LSI 9400-16i Raid card SAS/SATA/NVME SFF-8643 SAS3416 PCIe 3.1 x8 HBA
$155.27
Broadcom 9560-16I RAID Card SAS/SATA/NVME 8G cache SAS3916 PCIe 4.0 SFF8654
$727.00
Adaptec ASR-81605ZQ 12G SAS 16-Port 1GB Cache PCIe x8 RAID Controller
$131.99
LSI 9207-8i 8-Port SAS Non-RAID 6GBPS PCIe Host Bus Adapter
$34.95
Inspur LSI 9300-8i Raid Card 12Gbps HBA HDD Controller High Profile IT MODE
$15.98
LSI MegaRAID 9361-8i 12Gb PCIe 8-Port SAS/SATA RAID 1Gb w/BBU/CacheVault/License
$39.95
ORICO Multi Bay RAID Hard Drive Enclosure USB 3.0/ Type-C For 2.5/3.5'' HDD SSDs
$82.49
LSI MegaRAID 9361-8i 12Gbps PCIe 3 x8 SATA SAS 3 8 Port RAID + BBU & CacheVault
$39.00
ACASIS 2.5/3.5 inch 2 Bay SATA USB 3.0 Hard Drive Disk HDD SSD Enclosure 4 RAID
$58.99
NEW LSI MEGARAID SAS 9361-8i 12GB/s SAS + SATA RAID CONTROLLER CARD PCIe x8 3.0
$99.00