-
Knoppix shows eth0 and eth1, but I have 1 NIC
I am running Knoppix 4.0 HD Install from DVD.
During bootup, netcardconfig or ifconfig, I see 2 NICs (eth0 and eth1) but I only have 1 physical NIC (I do not have built in wireless.)
eth0 fails to get an address via DHCP or work with a static IP, and eth1 gets an address via DHCP.
I'd like to configure Knoppix to use the interface name eth0 rather than eth1 and ignore the phantom card.
Thanks
-
Administrator
Site Admin-
Re: Knoppix shows eth0 and eth1, but I have 1 NIC
Originally Posted by
chrisup
I am running Knoppix 4.0 HD Install from DVD.
Does Knoppix work correctly when booted from the DVD, not from the install? From years of watching these forums I would say that the networking failing after a hard disk install is the most common Knoppix install problem (and things like this are a major reason why many of us advise against hard disk installs of Knoppix).
-
Thanks for the reply.
The live DVD behavior is the same as the HD install.
I like the Knoppix HD install because it is less time consuming than most distros, and has all the packages I need ready to go. (I'm sort of lazy)
-
Knoppix shows eth0 and eth1, but I have 1 NIC
I think I see what your saying, so, this might be part of the answer.
Even though there's not a card physicly present at the lan port location you mention. Knoppix's start-up routine, by default, will turn the software for both lan ports (eht0 & eth1) ON, and, attempts to broadcast a DHCP ID signal for other available computers on a network.
It may take a few more seconds to boot, but, I've not seen an adversy effects to the system, other then a slight delay till the ports times out.
Apparently this is on the DVD, and, carries over to a hard drive installation.
You should be able to disable this somewhere in the startup routine, if it's disturbing you. which I'm syre someone else knows better about.
-
Senior Member
registered user
if there is a firewire port on that computer it might be seen as a ethernet card.
-
I do have a built-in firewire port. Unless you have an easy suggestion to disable the firewire networking I think I'll accept the eth1-eth0 scenario. Thanks for the replies so far everyone.
Similar Threads
-
By R. Henze in forum German Forum
Replies: 0
Last Post: 07-17-2007, 07:17 AM
-
By R. Henze in forum Hardware & Booting
Replies: 0
Last Post: 07-14-2007, 08:34 AM
-
By Micodat in forum Hardware & Booting
Replies: 0
Last Post: 06-27-2006, 07:11 AM
-
By paradigm_shift in forum Networking
Replies: 0
Last Post: 07-15-2005, 05:41 AM
-
By HAiRYANiMAL in forum General Support
Replies: 9
Last Post: 05-19-2003, 01:07 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
CISCO 5108 Blade Server Chassis N20-C6508
$200.00
DELL POWEREDGE M620 SERVER BLADE INTEL XEON E5-2670 @ 2.60GHZ 128GB RAM 2X 146GB
$399.00
HPE BL460c G9 ProLiant Blade | 2x Xeon E5-2620V3 | NO RAM | P244BR | 2xHDD Tray
$179.00
DELL PEM640 POWEREDGE M640 BLADE SERVER
$539.95
HP ProLiant BL460c G9 (Gen9) 2x E5-2670V3 12 Core 3.1GHz No Ram or No Drives
$59.98
Cisco UCS B200 M4 Blade Server, 2x2660 V3, 40GbE, No Ram No HDD
$35.95
Dell PowerEdge M620 0F9HJC Blade Server 2*E5-2670 2.60GHz 192GB RAM 2*300GB SAS
$103.99
Cisco UCS B200 M4 Blade Server 2X E5-2697A V4 18C 36T 2.60GHZ 768GB RAM No HDD
$1000.00
HP ProLiant BL460c Gen9 Blade 2x E5-2680v3 2.5GHz =24 Cores 256GB P246 650FLB
$430.00
Dell PowerEdge M620 Blade Server
$39.99