-
problem connecting to internet
hey
I cannot connect to internet with knoppix. I've searched the faq and the forum to find a way so solve it byt haven't found a way to do it. I'm really not that good at the whole computer thing so I might not understand everything but I'll do my best. My networkcard is a Realtek RTL8169/8110 Family Gigabit ethernet NIC. I have no clue what that means myself but it might be usefull. my connection is ADSL through a router. I read another answer were someone said it might help do run a netcardconfig and when i do it says it's ok. so it seems to find my networkcard but I can't connect to any site. my router is a Netgear WGR614. It's a wireless router but I'm not using the wlan right now. I don't know if there is any more information i need to give.
thanks.
PS. You'll have to excuse my poor english but since I'm not from US och UK or any other english speaking country I hope I'm excused
-
Administrator
Site Admin-
1) Are you sure that you are not connected to the Internet? (Yes, this has really happened here so it's worth asking again).
2) Please post the output of the command "ifconfig".
---
Verifying of md5 checksum and burning a CD at slow speed are important.
-
Junior Member
registered user
Re: problem connecting to internet
Originally Posted by
covox
hey
I cannot connect to internet with knoppix. I've searched the faq and the forum to find a way so solve it byt haven't found a way to do it.
If your ifconfig shows that you have a correct IP address, try pinging a website for example:
ping www.google.com
If you can ping a website correctly but still can't browse any website, then enter this on the address prompt of your browser about:config. A whole list of parameters should be listed below. Look for parameter network.dns.disableIPv6 , the default value for this parameter is false. Change it to true by double clicking on it. You should be able to browse internet after changing this parameter to true. I also had a similar problem the first time I used Knoppix.
I hope this helps.
Cheers!
-
I've tried to connect to google but i always fail. so yeah I'm not connected or at least theres a problem.
ifconfig showed this:
Link encap: Lovsl loopback
inet addr: 127.0.0.1 Mask: 255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets: 18 errors: 0 dropped: 0 overruns: 0 frame: 0
TX packets: 18 errors: 0 dropped: 0 overruns: 0 frame: 0
collisions: 0 txqueuelen: 0
RX bytes: 900 (900.0 b) TX bytes: 900 (900.0 b)
I don't know how to ping a website but I changed the setting in about:config and nothing happened.
-
Junior Member
registered user
Originally Posted by
covox
I've tried to connect to google but i always fail. so yeah I'm not connected or at least theres a problem.
ifconfig showed this:
Link encap: Lovsl loopback
inet addr: 127.0.0.1 Mask: 255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets: 18 errors: 0 dropped: 0 overruns: 0 frame: 0
TX packets: 18 errors: 0 dropped: 0 overruns: 0 frame: 0
collisions: 0 txqueuelen: 0
RX bytes: 900 (900.0 b) TX bytes: 900 (900.0 b)
.
Can you execute this command ifconfig eth0 from a terminal window?
This will show the first configured network card in your system.
-
yeah I think I can do that but I'm not sure that's the one that I'm using. for when I'm doing a netcardconfig eth0 fail. eth1 is my wlan and eth2 is ok
But sure I can do that and post back the results. I guess that execute the command ifconfig eth2 would do the same thing but for eth2 instead? And I'm not really sure what the difference is between eth0 eth1 and eth2 and why theres a difference so it would be nice if you could tell me. I'll post the results anyway
-
ok.
first. the result of ifconfig eth0 was:
Link encap: ÄUNSPEC HWaddr 00-03-0D-49-71-E3-1D-1C-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU: 1500 Metric: 1
RX packets: 0 errors: 0 dropped: 0 frame: 0
TX packets: 0 errors: 0 dropped: 0 carrier: 0
collisions: 0 txqueuelen: 1000
RX bytes: 0 (0.0b) TX bytes: 0 (0.0b)
I also did ifconfig eth2 and this was the result:
Link encap: Ethernet HWaddr 00-03-0D-36-96-12
inet addr: 192.168.0.2 Bcast: 192.168.0.255
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3459 (3.4 KiB) TX bytes: 3512 (3.4 KiB) Interrupt: 19 Base address: Oxcc00
-
I just realised I've made a misstake. it's not meant to stand ÄUNSPEC but UNSPEC. but I think you all realised that. I've must have been writing to fast and not noticed that I got som letters extra
-
Administrator
Site Admin-
It certainly looks like your hardware on eth2 is connected and got a proper DHCP setup, although why you seem to have a eth0 and eth2 but not eth1 isn't clear. Once again I'm wondering if you are not really connecting just fine but don't realize it, in the past some people have thought they were not conneced when indeed they were. Alternately, it might be an ip6 vs ip4 issue, I can't rule that out but I see no sign it is. Another fix for ip6 problems tends to be to change dns servers.
You ping an ip address or url by typing ping and the address at a shell prompt, as in ping www.knoppix.net or ping 72.36.188.40
You should also try accessing the knoppix.net site by both the above url and the above ip address. If the ip address works but the url does niot then it is a DNS issue.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
-
I can't swear I'm not connected but when I write a url and press enter in both konqueror and iceweasel it says it can't find the server or something like it.
I will try to ping both the url and the ip now.
Similar Threads
-
By garrincha in forum Networking
Replies: 7
Last Post: 05-24-2006, 04:33 AM
-
By -=Unstoppable=- in forum Networking
Replies: 2
Last Post: 12-10-2005, 10:12 PM
-
By P.Enguin in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 09-26-2004, 06:31 PM
-
By Randomi in forum General Support
Replies: 3
Last Post: 01-19-2004, 12:16 AM
-
By samboy in forum Networking
Replies: 6
Last Post: 11-10-2003, 09:45 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
HP ProLiant DL380 Gen9 8SFF Server - E5-2698 v3 - 32Cores - 128GB Ram - 1TB HDD
$299.00
Dell Poweredge R730xd 2.5in 2x E5-2690 v3 2.6ghz 24-Cores 64gb H730 2x 750w
$189.99
DELL PowerEdge R630 10 Bay SFF 2x E5-2620v4 2.1GHz =16 Cores 32GB H730 4xRJ45
$248.00
HP ProLiant DL360 Gen9 Server 2x E5-2620v4 2.1GHz =16 Cores 32GB P440AR 4xRJ45
$229.00
Dell PowerEdge R620 Server 2x E5-2660 v1 2.2GHz 16 Cores 256GB RAM 2x 300GB HDD
$89.99
Dell R630 Server 2x E5-2620 V4 2.1GHz =16 Cores 128GB DDR4 1x 960GB 2x 1G 2x 10G
$210.00
Dell PowerEdge R730XD 28 Core Server 2X Xeon E5-2680 V4 H730 128GB RAM No HDD
$389.99
Dell PowerEdge R720XD Xeon E5-2680 V2 2.8GHz 20 Cores 256GB RAM 12x4TB
$510.00
Lenovo x3550 M5 1U Server 2x Xeon E5-2680 v4 2.4ghz 28-Cores 128gb M5210 2x750w
$399.99
CTO Dell PowerEdge R630 Server, 2x Xeon E5-2680V4, 64GB- 512GB RAM, New SSDs
$354.67