is that possible ? I believe in order for this to happen, the linksys must also support bridge function or the packet on the other side just won't come over(and vice versa).
Why not just 2 sub-net which would make things simpler ?
As of right now at my home I have setup knoppix as a dialup router, and I'm pretty well versed in linux routers. The issue I'm facing is that I'm fixing to move into a home I purchaced next to my parents house, and I would like to network the two houses together wirelessly. Here is the plan.
What I would like to do is have a Linksys WAP11 access point at my mom's house and use a knoppix box at my house that has a WUSB11 adapter and a regular network card and bridge eth0 and wlan0.
Here is the setup I would like:
(mom's house);
home router[2.254]------> wap11[2.253] -->
++wireless hop+++
(my house);
knoppix wifi card[2.252]--------> knoppix eth0[2.251]------> my switch--------> my wap11 for my home network[2.250]-------> my wireless laptop[2.118]
My desktop would also be plugged into my switch with the address of [2.249]
Is this possible? I would rather have everything on one subnet instead of having 192.168.3.0 network at my house and 192.168.2.0 at her house and the wifi side of my knoppix box with knoppix acting as a router between subnets. I know it wouldn't be routing because you don't route packets on the same subnet, but is there a way to do this with iptables just to bridge eth0 and wlan0? I guess I'm trying to make knoppix into a poor mans linksys WET11 Wireless bridge.
Sorry for the long post, but I figured it was best to explain the whole situation.
Thanks!
is that possible ? I believe in order for this to happen, the linksys must also support bridge function or the packet on the other side just won't come over(and vice versa).
Why not just 2 sub-net which would make things simpler ?
The linksys WAP11 supports a bridge function, but instead of using the WAP11 in bridge mode, I was going to put it in infrastructure mode and set it up in a window at my moms and put the wireless adapter on my knoppix box in a window at my house, and just have the knoppix box be a client off of the WAP11.
I just didn't want to have a seperate subnet on the eth0 side of my knoppix box. I would rather have eth0 and wlan0 be on the same subnet and have the traffic from my house to her's pass transparently through the knoppix machine.
What you are proposing is not only feasable but I am doing it, though I am not using knoppix in my bridge I am using OpenBSD, but the configuration should roughly be the same. What you are doing is turning a$700 computer into a $5.00 bridge.
in the /etc just configure the interfaces:
not as dhcp
not to a static ip but as "up"
example
hostnamexl0
#dhchp
#inet
up
then
hostnamexl11
#dhcp
#inet
up
you can also add packet filtering or have the bridge do NAT
since you want to use knoppix though and knoppix is debian based I reccomend you read the following: http://www.wlug.org.nz/WirelessEthernetBridge
take care and good luck,
Thanks for the replies!
I think I'm going to just get 2 WAP11s and call it a day. Although, I will attempt this project just for the sake of knowing how to do it.
I do however wish that a wireless bridge was $5, I would use them for everything! Unfortunatly the linksys WET11 wireless bridge is more expensive than a WAP11. So what do I do, buy a WAP11 and put it in bridge mode.
You may want to take a look at this post.
http://www.knoppix.net/forum/viewtopic.php?t=663#2561
ALLEN BRADLEY 281G-F12S-10B-RRG-CBG /C AMORSTART MODULE 280G-FS-10-RG STK 2911
$332.50
Intel Core i5-8500 Six Core Desktop PC CPU Processor 3.00GHz LGA1151 SR3XE
$49.99
Intel Core i9-12900KF - 12th Gen Alder Lake 16-Core (8P+8E) 3.2GHz LGA CPU
$262.99
AMD Ryzen 9 7900X3D Gaming Processor - 12 Core And 24 Threads - 5.60 GHz Max Boo
$329.99
Intel Core i7-3770K 3.5GHz Quad-Core (BX80637I73770K) Processor
$49.00
Intel Core i5-7600 3.8GHz Quad-Core Processor SR334 LGA1151
$34.99
Intel Core i7-14700KF Unlocked Desktop Processor
$430.64
Intel Core i5-9500 SRF4B 3.00GHz Six Core LGA1151 Processor
$65.00
Intel Xeon E5-2673 v4 20-Core 2.30GHz 50MB 9.60GT/s 135W Processor SR2KE
$78.99
Intel Core i5-8500 3.00GHz SR3XE Socket 1151 6 Core CPU Processor
$55.00