If your problem is what to do with an iso, see if this helps:
http://www.psychocats.net/ubuntu/iso
Ignore the cat.
Hi i've been trying to make a knoppix cd but when i use the cd it says there is no bootable program. I used roxio easy cd dvd creator. So i tried to download another version of knoppix but that didn't work too. Is it possible that the cd doesnt work because i only put the iso file unto the cd and not that other files(there were 4 little files which are a few kb big). So i tried to ut them unto the cd also but i can only put one file onto the cd!
any suggestions????
If your problem is what to do with an iso, see if this helps:
http://www.psychocats.net/ubuntu/iso
Ignore the cat.
@tok121
Did you read the Downloading FAQ in the wiki? There is a section
Q: I have downloaded the ISO file. How do I burn the ISO? How is the ISO supposed to be burned? http://www.knoppix.net/wiki/Download...o_be_burned.3F
I use ImgBurn http://www.imgburn.com/ to burn ISO image files.
@klaus2008
Hi, klaus.
Since I've already admitted to not being an expert, I can also admit that
I could not readily find an answer using any of the forum's search boxes.
I'm not sure I even found any relevant FAQ or Wiki on this.
Are you sure it's still here?
This was really hard to find:
http://www.knoppix.net/wiki/Download...o_be_burned.3F
If we didn't have the link.
Last edited by utu; 08-05-2010 at 06:13 PM.
Outside the forum, with the search key in Google
knoppix burning iso
Your entry shows up as #1.
The forum itself gives this up rather grudgingly.
Hi, utu
You don't have to do a search from outside because the website KNOPPIX.net has got a search page http://www.knoppix.net/s.html
That is because the forum isn't the right place to look for documentation. The forum is for discussion. The wiki is for documentation. And it is reached by the "Documentation" link on the top of every forum page. (Imagine that!) Once a user gets to the wiki, the proper section to read is the "Downloading FAQ" which gives all of the information needed to properly download and verify the download and then burn to CD properly. We have seen all of the typical errors over and over again. They could all be found by extensive searching of the forums, but that would be pointless, they are all neatly organized in one place in the FAQ.
---
Verifying of md5 checksum and burning a CD at slow speed are important.
Exactly my point.
ARUBA J9772A 2530-48G PoE+ 48 PORT ETHERNET SWITCH W/ RACK EARS J9772-60301
$140.23
Fortinet FortiSwitch FS-124D-POE 24 Port Gigabit Ethernet Switch UNREGISTERED
$99.97
Brocade ICX 7250-48 48-Port Gigabit Ethernet Network Switch | ICX7250-48-2X10G
$84.95
HPE ARUBA 2530-24G J9773A PoE+ 24-PORT GIGABIT ETHERNET SWITCH J9773-60201
$98.15
NETGEAR GS305300PAS 5 Port Gigabit Ethernet Unmanaged Switch
$15.99
DELL POWERCONNECT (6248) 48-Port Network Switch W/Rack Ears And Power Cable
$39.95
NETGEAR 8-Port Gigabit Ethernet Unmanaged Switch GS308 300 Switch series
$27.27
TP-Link TL-SG108PE 8-port Gigabit Easy Smart PoE+ Swith w/ 4-port PoE - Sealed
$49.50
Brocade ICX 7250 (ICX725048P2X10G) Enterprise Network Switch with 48 LAN Ports
$99.00
Cisco SG300-52-Port Gigabit Managed Rack Mountable Network Switch
$44.95