-
Originally Posted by
Carlos_E_Morimoto
Try "fb 1024x768" (without "knoppix", just fb 1024x768 at boot line) this works with my two LCD monitors
In Italian market my 38B1 is Known or equivlent to 38B2 in other countries and a datasheet is viewable here:
http://www.fujitsu-siemens.com/rl/pe...8b2basic.html#
However :
Frequencies
Horizontal 30 - 60 kHz
Vertical 55 - 75 Hz
and 102x768 is supported with the refresh of 60 hz (48.36, 48.78 KHZ), 70 HZ (56.48 KHZ) ,72 HZ (57.52 KHZ), 75 HZ (60.02 KHZ and 60.24 KHZ)
Thanks for very tips to all
Rob
-
the entire situation
Using Matrox G400 16 MB and Fuitsu Siemens 38B1 at the startup I tried many tips of you( in combination too) and other tips of F2 screen
Then the message is the following
"You passed an undefined mode number. Press RETURN to see mode Vesa mode vailable.. I tried 0 (80x25 ) or 3 (80x2.
It is ok. The coloured text is good and so I can see many hardware well recognized and among these there is Matrox G400 16 MB AGP using XFree86 server - fbdev)
and a generic monitor voice
Tryng fb102x768 the screen is blinking, trying to start X11..
then I can read in text mode:
trying XFree (vesa)...failed
trying XFree (fbdev) ...failed
and then I return to command prompt
What do you think about this?
thanks
Rob
-
Does somebody have a clue, how to get knoppix running with a sony cpd-m151 tft lcd?
-
Senior Member
registered user
Undefined mode number
Hi I gete the same thing on bootup on my COMPAQ presario 1247 laptop. It says the same thing about passing an undefined mode number, and to wait or press space bar to continue, which i always do [press space bar] and it seems to work fine when KDE starts....I did dmesg and looked for any video related errors but found nothing....So I have no idea why it does that but it doesnt seem to be a problem.....i will look into this closer cause i would like it to start with no errors so i dont have to keep hitting the space bar every time! bob
-
hi all!
I have a similair problem with mine. i have a old Hewlitt Packard Pavilion monitor. and i also get the you have passed a undefined number to press return for video modes or press space bar to continue. everything seems to load ok and everythings detected. even my monitor but it detects it as a generic monitor. but anyway. it loads but when it gets to where your GUI is sposed to load, all i get is a flicker and then nothing but a black screen. I tried different video modes, tried the xmodule options. even tried telling it to run kde thinking it might be a compatability issue with one of the gui programs. but no such luck. my graphics card is a intel(r) 82810 graphics controller. when i had mandrake linux on my system i had no troubles running. don't have it now. i just have windows xp. I have 128 mb ram. hope this info helps. was hoping some one could help me. thankssss[/b]
-
Senior Member
registered user
If you have problem starting up X, check /etc/X11/XF86Config-4 and remove those modline entries and try again(startx at the command line), especially for LCD monitors.
-
umm i am a total noob to this lol i know to start it u just type x or xmodule at boot but have no idea how to do the rest. lol thanks
Sanny
Similar Threads
-
By dragonforce99 in forum Hardware & Booting
Replies: 3
Last Post: 07-08-2004, 11:45 PM
-
By nicorelli in forum General Support
Replies: 0
Last Post: 07-01-2004, 12:09 AM
-
By gyro in forum Hardware & Booting
Replies: 1
Last Post: 01-10-2004, 10:31 PM
-
By Simon_Haddad in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 10-27-2003, 06:23 AM
-
By ledatica in forum Laptops
Replies: 4
Last Post: 10-15-2003, 08:36 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
1U IBM x3550 M5 4 Bay SFF SAS3 Server 2x E5-2683 V3 28 Core 128GB DDR4 2x Tray
$318.00
IBM Power S822 8284-22A 12SFF Power8 3.89GHz 6Core 64GB RAM No HDD Server System
$359.99
IBM X3650 M5 8871-AC1, 2 X E5-2620V4 2.1 GHZ,20M, 32 GB, DUAL 750W, 2 X 1TB HDD
$369.99
IBM Power S822 12-Bay Server System Power8 Core 3.42Ghz DVD-Rom Drive 64GB No HD
$349.99
VINTAGE IBM PC SERVER MODEL 320 8640 J
$325.00
IBM mainframe server cpu IBM93 vintage cpu collector's item
$129.99
IBM System x3250 M4 Server Intel Xeon E3-1220 3.10GHz 8GB RAM No HDDs
$60.56
IBM Server eServer | IBMR1000 | UPS 1000VA 700W W/New Batteries
$115.00
IBM Power S822 8284-22A 12SFF Power8 3.89GHz 6-Core 64GB RAM No Bezel/HDD Server
$319.99
IBM Lenovo X3650 M5 2U 8x 2.5” CTO Rack Server – 2x HS, 2x 750W
$199.00