-
Junior Member
registered user
alright...so I finally got ALSA working...and I got my NIC working...but I need to modprobe 8139too and then netcardconfig everytime I boot! I added 8139too as well as mii and crc32 to the end of /etc/modules, even did an update-modules, but no luck with getting it to boot at startup....and actually now that i just looked again...both emu10k1 and 8139too were already in the list right next to each other (funny coincidence i'm assuming). hmm...here's my current /etc/modules:
Code:
rtc
apm power_off=1
usb-uhci
printer
mousedev
hid
serial
parport_pc
bttv
tuner
emu10k1-gp
8139too
via82cxxx_audio
emu10k1
agpgart
nls_cp437
nls_iso8859-1
ext3
reiserfs
af_packet
autofs4
mii
crc32
and here's my current lsmod (after using modprobe 8139too to open 8139too, mii and crc32)
Code:
8139too 17408 0
mii 4032 1 8139too
crc32 3840 1 8139too
snd_pcm_oss 48420 0
nls_cp437 5376 4
snd_mixer_oss 16768 1 snd_pcm_oss
apm 15524 1
parport_pc 26860 1
lp 8836 0
parport 36392 2 parport_pc,lp
uhci_hcd 29840 0
ohci_hcd 15808 0
ehci_hcd 22596 0
evdev 7680 0
snd_emu10k1 64004 4
snd_rawmidi 20000 1 snd_emu10k1
snd_pcm 86180 4 snd_pcm_oss,snd_emu10k1
snd_timer 21252 1 snd_pcm
snd_ac97_codec 51716 1 snd_emu10k1
snd_page_alloc 9028 2 snd_emu10k1,snd_pcm
snd_util_mem 3264 1 snd_emu10k1
snd_hwdep 7264 1 snd_emu10k1
snd 43940 15 snd_pcm_oss,snd_mixer_oss,snd_emu10k1,snd_rawmidi,snd_pcm,snd_timer,snd_ac97_codec,snd_util_mem,snd_hwdep
soundcore 7392 1 snd
root@tux:~# lsmod
Module Size Used by
8139too 17408 0
mii 4032 1 8139too
crc32 3840 1 8139too
snd_pcm_oss 48420 0
nls_cp437 5376 4
snd_mixer_oss 16768 1 snd_pcm_oss
apm 15524 1
parport_pc 26860 1
lp 8836 0
parport 36392 2 parport_pc,lp
uhci_hcd 29840 0
ohci_hcd 15808 0
ehci_hcd 22596 0
evdev 7680 0
snd_emu10k1 64004 4
snd_rawmidi 20000 1 snd_emu10k1
snd_pcm 86180 4 snd_pcm_oss,snd_emu10k1
snd_timer 21252 1 snd_pcm
snd_ac97_codec 51716 1 snd_emu10k1
snd_page_alloc 9028 2 snd_emu10k1,snd_pcm
snd_util_mem 3264 1 snd_emu10k1
snd_hwdep 7264 1 snd_emu10k1
snd 43940 15 snd_pcm_oss,snd_mixer_oss,snd_emu10k1,snd_rawmidi,snd_pcm,snd_timer,snd_ac97_codec,snd_util_mem,snd_hwdep
soundcore 7392 1 snd
Seems like there's lots of stuff in there that isn't being loaded...though I just looked through and some of that stuff like bttv and tuner are left over from 2.4.2x
-
Senior Member
registered user
What does the /etc/network/interfaces file look like that is where the IP for the card gets set and if auto eth0 is in there then it is brought up automatically on boot.
For static settings it should look similar to this you would need to replace the settings with yours.
Code:
>$ cat /etc/network/interfaces
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface
auto lo
iface lo inet loopback
# The first network card - this entry was created during the Debian installation
# (network, broadcast and gateway are optional)
auto eth0
iface eth0 inet static
address 192.168.0.1
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
gateway 192.168.0.254
For DHCP
Code:
>$ cat /etc/network/interfaces
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface
auto lo
iface lo inet loopback
# The first network card - this entry was created during the Debian installation
# (network, broadcast and gateway are optional)
auto eth0
iface eth0 inet dhcp
You can remove or put a # character in front of the lines that are still left over from the knoppix kernel like the bttv, tuner and emu10k1 if they are not needed anymore. The modules being loaded are for the new kernel if you did not compile the others that are in the modules file then they would never have a chance to be loaded they do not exist for that kernel.
-
Junior Member
registered user
Code:
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface
# automatically added when upgrading
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
doesn't seem to be the problem
Similar Threads
-
By andromeda in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 04-23-2004, 01:36 PM
-
By NerdIII in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 03-25-2004, 01:30 AM
-
By AKengineer in forum Hdd Install / Debian / Apt
Replies: 2
Last Post: 09-01-2003, 08:27 PM
-
By laffer in forum Hardware & Booting
Replies: 1
Last Post: 08-06-2003, 08:35 PM
-
By jonwood in forum Hardware & Booting
Replies: 4
Last Post: 03-24-2003, 04:37 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
IBM 8203 E4A p520 Server 8203-E4A 4.2GHz 2-Core POWER6 32GB RAM / NO HDD USED
$99.99
IBM Power S822 12-Bay Server System Power8 Core 3.42Ghz DVD-Rom Drive 64GB No HD
$399.99
ibm server z series
$16000.00
IBM System x3250 M4 Server Intel Xeon E3-1220 3.10GHz 8GB RAM No HDDs
$49.74
IBM Power 720 POWER7 00E6516 3.6GHz CPU 64GB RAM Server
$209.98
IBM Power 740 8205-E6C Express 8-SFF Power7 3.55GHz CPU 64GB RAM *No HDD* Server
$191.99
IBM 7944AC1 System x3550 M3 Server 1*Intel Xeon X5650 2.67GHz 4GB SEE NOTES
$26.97
IBM System x3550 M4 Server 2 x Intel Xeon E5-2609 36GB RAM No HDDs
$68.84
IBM Power S822 8284-22A 2.5" 12-Bay 64GB 2X 00ND478 2X 00E2865 *READ*
$599.99
IBM Lenovo X3650 M5 2U 8x 2.5” CTO Rack Server – 2x HS, 2x 750W
$199.00