-
6.7.1 DVD Weakest Link
RE: 6.71 DVD weakest Link: Network Functionality
# MD5 checksums generated by MD5summer (http://www.md5summer.org)
# Generated 2/15/2012 9:11:08 PM
90c0a0acbbd954145b6f55ca36e2e87f *KNOPPIX_V6.7.1DVD-2011-09-14-EN.iso_EXP
90c0a0acbbd954145b6f55ca36e2e87f *KNOPPIX_V6.7.1DVD-2011-09-14-EN.iso_ACT
Hi,
1) Only Chromium browser functions ok.
2) 6.7.1 Firewall does not recognize Persistent 'Knoppix-data.img'?
3) MAC80211 stack/b43 wireless card driver missing?
Any help/support?
THX
Luther, new to the Linux world!
PS. Mint installed OotB following:
apt-get install b43-fwcutter
apt-get install b43-fwcutter firmware-b43-installer
*******
knoppix@Microknoppix:~$ sudo ifconfig
eth0 Link encap:Ethernet HWaddr 00:0f:b0:fa:e5:31
inet addr:192.168.0.71 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::20f:b0ff:fefa:e531/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:507 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:31480 (30.7 KiB) TX bytes:1272 (1.2 KiB)
Interrupt:22 Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:440 (440.0 B) TX bytes:440 (440.0 B)
knoppix@Microknoppix:~$ lspci -vnn | grep 14e4
06:02.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g
Wireless LAN Controller [14e4:4318] (rev 02)
knoppix@Microknoppix:~$ sudo unname -a
sudo: unname: command not found
knoppix@Microknoppix:~$ lspci -vvn|grep 43 -a7
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
<SERR- <PERRBridgeCtl:
Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2BPriDiscTmr-
SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
knoppix@Microknoppix:~$ sudo dmesg
: No partition found (1)
[ 2.395325] scsi 2:0:0:0: Direct-Access Lexar USB Flash Drive 8.07 PQ: 0 ANSI: 2
[ 2.395843] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 2.396934] sd 2:0:0:0: [sdb] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 2.397426] sd 2:0:0:0: [sdb] Write Protect is off
[ 2.397430] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2.397927] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2.397930] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2.400312] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2.400315] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2.523709] attempt to access beyond end of device
[ 2.523714] sda3: rw=0, want=66, limit=2
[ 2.523718] isofs_fill_super: bread failed, dev=sda3, iso_blknum=16, block=32
[ 2.531690] attempt to access beyond end of device
[ 2.531695] sda3: rw=0, want=18, limit=2
[ 2.531702] REISERFS warning (device sda3): sh-2006 read_super_block: bread failed (dev sda3,
block 8, size 1024)
[ 2.531709] attempt to access beyond end of device
[ 2.531712] sda3: rw=0, want=130, limit=2
[ 2.531717] REISERFS warning (device sda3): sh-2006 read_super_block: bread failed (dev sda3,
block 64, size 1024)
[ 2.537042] attempt to access beyond end of device
[ 2.537045] sda3: rw=0, want=4, limit=2
[ 2.537049] EXT4-fs (sda3): unable to read superblock
************
-
konqueror trace
Hi,
Typing "konqueror" on the command line provides this trace log:
**********
Connecting to deprecated signal
QDBusConnectionInterface::serviceOwnerChanged(QStr ing,QString,QString)
kbuildsycoca4 running...
konqueror(3456)/kdecore (KLibrary) findLibraryInternal: plugins should not have a 'lib' prefix:
"libkhtmlpart.so"
konqueror(3456)/kdecore (KLibrary) kde4Factory: The library "/usr/lib/kde4/khtml_kget.so" does
not offer a qt_plugin_instance function.
konqueror(3456)/kdecore (KLibrary) findLibraryInternal: plugins should not have a 'lib' prefix:
"libkhtmlpart.so"
konqueror(3456)/kdeui (kdelibs): Attempt to use QAction "iceweasel" with KXMLGUIFactory!
konqueror(3456)/kdeui (kdelibs): Attempt to use QAction "epiphany" with KXMLGUIFactory!
konqueror(3456)/kdeui (kdelibs): Attempt to use QAction "" with KXMLGUIFactory!
QSslSocket: cannot resolve SSLv2_client_method
QSslSocket: cannot resolve SSLv2_server_method
QPainter::begin: Widget painting can only begin as a result of a paintEvent
QPainter::translate: Painter not active
QPainter::setClipRect: Painter not active
QPainter::hasClipping: Painter not active
QPainter::setPen: Painter not active
QPainter::setBrush: Painter not active
QPainter::drawRects: Painter not active
************
Your comments?
Thanks for your support,
Luther
-
Jump Started
Hi,
Plugging the DNS settings into X's network-admin, got internet connection jump started.
On a live USB, there appears a dummy lock for network-admin.
Question 1:
Can n-a settings be saved on the flash stick?
Question 2:
What is the network-admin equivalent for Adriane, so Elinks can get connected to the internet?
Kind Regards,
luther
-
Hi, 1) Only Chromium browser functions ok.
2) 6.7.1 Firewall does not recognize Persistent 'Knoppix-data.img'?
3) MAC80211 stack/b43 wireless card driver missing?
How do you use your Knoppix DVD download? From DVD, flash disk install, HD installation?
First of all try the cheatcode "knoppix testcd".
-
Originally Posted by
Werner P. Schulz
How do you use your Knoppix DVD download? From DVD, flash disk install, HD installation?
First of all try the cheatcode "knoppix testcd".
Hi,
"knoppix testcd" reported:
Checking KNOPPIX/background.jpg ... Failed!
Checking KNOPPIX/SOURCES.TXT ...
Continue anyway? [ y/N ]
Chromium reported:
Error 137 (net::ERR_NAME_RESOLUTION_FAILED): unknown error
~~~~~~~~~~~
Please refer to:
http://www.mninter.net/~pfourier/screen1.zip
This zip shows installed flash stick footprint and
the reason why background.jpg failed 6.7.1 testcd.
Thanks for reply, Werner!
luther
PS. HD install cannot work on this USB setup.
-
"knoppix testcd" reported:
Checking KNOPPIX/background.jpg ... Failed!
If "knoppix testcd" reports any error, especially within KNOPPIX, there is no need to analyze your other curious problems. The DVD is damaged!
Burn another DVD and test the integrity first.
Last edited by Werner P. Schulz; 03-31-2012 at 10:48 AM.
-
Originally Posted by
Werner P. Schulz
If "knoppix testcd" reports any error, especially within KNOPPIX, there is no need to analyze your other curious problems. The DVD is damaged!
Burn another DVD and test the integrity first.
Dear Werner: My previous post was a testcd of the USB device (flash). At your suggestion, the actual DVD testcd results were:
Code:
knoppix 6 found at: /dev/sr0
Checking KNOPPIX/KNOPPIX ... All files OK.
I'm sending this post from 6.7.1 flash install w/Iceweasel. The TRICK was to plug the correct NAMESERVER address into "netcardconfig", e.g.:
In netcardconfig, "nameserver" defaults to "gateway", which must be changed to get internet connection to the router port. The new "nameserver" address cannot be saved to flash, so it simply has to be entered each session.
My question is, what is the "netcardconfig" equivalent for Adriane? I see NO mention of "nameserver" in Adriane, that Elinks can reference. Elinks DOES function in X-desktop, but doesn't in Adriane. Thanks for the reply! luther
Last edited by Werner P. Schulz; 04-01-2012 at 08:59 AM.
Reason: formatted by moderator
-
2) 6.7.1 Firewall does not recognize Persistent 'Knoppix-data.img'?
There is an error in the script
http://lists.debian.org/debian-knopp.../msg00001.html
sudo: unname: command not found
Try
I'm sending this post from 6.7.1 flash install w/Iceweasel.
Please tell us the output from
(the screenshot is confusing for me).
By the way, do you really need Adriane, the Knoppix version for blind people?
The NetworkManager Applet left the clock in the panel does not work for you?
-
Originally Posted by
Werner P. Schulz
There is an error in the script
http://lists.debian.org/debian-knopp.../msg00001.html
Try
Please tell us the output from
(the screenshot is confusing for me).
By the way, do you really need Adriane, the Knoppix version for blind people?
The NetworkManager Applet left the clock in the panel does not work for you?
Hi, I found this firewall patch on the forum: "sudo nano /usr/sbin/firewall" ** I changed "KNOPPIX.IMG" to "KNOPPIX-DATA" Shouldn't this be correct?
Please enlighten me on: "sudo: unname: command not found" and also: "uname -a"
Here is the output from code: df -h
Code:
knoppix@Microknoppix:~$ sudo df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sdb1 6.5G 6.5G 1.4M 100% /mnt-system
tmpfs 2.0G 0 2.0G 0% /ramdisk
/dev/cloop 8.7G 8.7G 0 100% /KNOPPIX
/dev/loop0 2.8G 885M 1.9G 32% /KNOPPIX-DATA
unionfs 2.8G 885M 1.9G 32% /UNIONFS
unionfs 2.8G 885M 1.9G 32% /usr
unionfs 2.8G 885M 1.9G 32% /home
tmpfs 10M 56K 10M 1% /UNIONFS/var/run
tmpfs 10M 2.8M 7.3M 28% /run
tmpfs 10M 0 10M 0% /UNIONFS/var/lock
tmpfs 100M 76K 100M 1% /UNIONFS/var/log
tmpfs 2.0G 12K 2.0G 1% /tmp
udev 20M 32K 20M 1% /dev
tmpfs 2.0G 148K 2.0G 1% /dev/shm
knoppix@Microknoppix:~$
The screenshot is confusing simply because I swapped out "background.jpg" with an earlier release. I can't imagine this mod effecting functionality. My question to you, Werner, is using a 1 GB Linix/Swap file in flash. Is it relevant?
As far as using Adriane, it appears the ONLY alternative to get Knoppix to work on my older hp dt PC with 95MB RAM. I'm quite sure "nameserver" defaults to "gateway", which needs to be changed inorder to get Elinks on the 'net, like it does w/X-desktop. The clock applet is excess baggage and can be removed, if possible. Thanks for replying to my post. luther PS. Posted w/6.7.1 flash installation
---------------------------------------
Please use the "Go Advanced" button to have more abilities to format the posting; before sending your posting use "Preview" to see how it looks like.
Last edited by Werner P. Schulz; 04-01-2012 at 07:40 AM.
Reason: formatted by moderator
-
If you allready changed the firewall script, it's ok.
unname != uname
You can start Knoppix with cheatcode "knoppix 2" to start with text-console.
Adriane uses "knoppix-network-manager" or alternativ "network-setup".
The other way to get the network-settings is: Type
within the console and then select "Setup".
Last edited by Werner P. Schulz; 04-01-2012 at 04:33 PM.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
1TB/2TB USB 3.0 Flash Drive Thumb U Disk Memory Stick Pen PC Laptop Storage lot
$580.99
Internal HDD SATA 3.5" 250GB-2TB Hard Drive with Legacy Windows 11 Pro Installed
$29.15
Type C USB 3.0 Flash Drive Thumb Drive Memory Stick for PC Laptop 1TB 2TB lot
$73.29
Samsung - 990 980 970 PRO & EVO 4TB 2TB 1 TB Internal PCle Gen 4x4 NVMe M.2SSD
$320.00
CISCO A03-D1TBSATA 1TB 7.2K 6G 2.5INCH SATA HDD
$9.00
1TB HDD/SSD 2.5" SATA Hard Drive for Laptop with Win 10/Win 11 Pro Pre-installed
$28.99
WD - Blue SN580 1TB Internal SSD PCIe Gen 4 x4 NVMe
$79.99
Samsung PM981 1TB NVMe M.2 2280 SSD MZ-VLB1T0B Lenovo SSS0L25156 00UP736
$40.99
1TB HDD/SSD 2.5" SATA Hard Drive Laptop with Windows 11 Pro Installed
$27.99
2019/20+ APPLE MACBOOK PRO 16 TOUCHBAR 32GB RAM 1TB SSD 8 CORE 5.0GHz i9 5500M
$897.00