I've booted Knoppix on a machine with a blank HD, it does work. Not sure if I've tried it with that particular version but at least with 3.3-2003-11-19.
I was trying to install KNOPPIX on a completely new computer by booting off the CD. The harddisks were not formatted or partitioned. I was hoping to boot into KNOPPIX and use fdisk to partition the hd. However KNOPPIX (3.3-2003-09-24) seems to stop when detecting the hds and trying to create the fstab entry.
What I did was to boot from a dos diskette and partition the hds. After that everything was ok.
Does that mean that KNOPPIX can only run if the hds are partitioned? Or is this because I must wait longer? Or is it because I am not using the lastest KNOPPIX?
I was hoping to do everything from one CD.
I've booted Knoppix on a machine with a blank HD, it does work. Not sure if I've tried it with that particular version but at least with 3.3-2003-11-19.
Windos_No_Thanks,
Stupid question here, but, how do you get the DATE version, that both of you are speaking of???
True, someone else d/l'ed my v3.3, and burned the ISO image for me, is that where you get the date version you both are using? (from the ISO file itself?) Or can you get this date version from a command in Knoppix?
All I knew about was the uname part, i.e. I have:
Knoppix v3.3 v2.4.22-xfs
Thanks for any enlightenment,
Cuddles
IIRC the text on the boot screen tells you exactly which version it is when booting from CD, I'm not sure if/where it can be found on a HD install though.Originally Posted by Cuddles
Hmmmmm, oh well...
To add (quality) to the thread...
I installed Knoppix 3.3 - the one I mentioned above (previous), from just the CD - completely new hard drive - not even a partition table on the drive - who knows why it didn't work for you though.
This was on my new system, only one hard drive, and no previous OS was on it.
Cuddles
Could it be that I am not patient enough to wait for the detection process to finish? I waited for about 3 mins.
Or is it because its a SATA harddisk?
Hmmmmmm,
Just for my knowledge, what is a SATA hard disk?
I am familiar with IDE, and SCSI, I know "of" Flash, and USB, but I have never heard of this one. I have been out of the "main-stream" computer technology for about two years, being in a small town now, things are less visible here...
Thanks for the enlightenment,
Cuddles
I think he is refering to Serial ATA. More information is available at http://www.serialata.org/. Which probably explains why markleong is having difficulties.
Are you saying that KNOPPIX will have problems with SATA harddisks? Or it only my version of KNOPPIX?
I do not know if Knoppix works with SATA harddrives, perhaps someone else knows.
Cisco Catalyst C9300-24UX-A 24 Port 10G/mGig UPOE Network Switch, no module
$399.97
NetGear ProSafe GS748T V4 48-Port Gigabit Smart Switch w/ Ears
$35.00
Dell X1018 X-Series Smart Managed Switches 16-Port Gigabit 2-Port SFP Switch
$65.00
Fortinet FortiSwitch FS-124D-POE 24 Port Gigabit Ethernet Switch UNREGISTERED
$99.97
New Linksys SE3005 5-port Gigabit Ethernet Switch
$18.99
Linksys SE3008 8 Ports Rack Mountable Gigabit Ethernet Switch
$21.99
New 10/100 Mbps 8 Ports Fast Ethernet LAN Desktop RJ45 Network Switch Hub
$11.49
TP-Link TL-SF1005D 5-Port 10/100Mbps Fast Ethernet Desktop Switch
$12.99
Brocade ICX7250-48P-2X10G 48-Port PoE+ Ethernet Network Switch TESTED
$104.95
ARUBA J9772A 2530-48G PoE+ 48 PORT ETHERNET SWITCH W/ RACK EARS J9772-60301
$125.69