The custom kernel howto should cover what you want to do. You should find the default config for the 2.6 kernel in /boot/
Hello!
I have Knoppix 3.4. I successfully used the knoppix-installer script to install Knoppix 3.4 on my hard drive. For a certain application (LFS 6.0 testing) I need a 2.6.* kernel compiled with GCC 3.*, and a "cat /proc/version" command tells me the K3.4 kernel is 2.6.5 compiled with GCC 2.<whatever>. Now I want to somehoe recompile the same 2.6.5 kernel with a newer GCC; however, the Knoppix remastering / custom kernel HOWTOs are a little above my level of knowledge and understanding... What I want to do is keep the current kernel configuration and just compile it; however I didn't find the kernel source code in /usr/src, and a configuration file only for the 2.4.*.... In short, I'm in need of advice how to proceed to get a working Knoppix with a 2.6.* kernel compiled with GCC 3.*
Thanks!
The custom kernel howto should cover what you want to do. You should find the default config for the 2.6 kernel in /boot/
Here's what I figured out myself. I downloaded the kernel source from http://developer.linuxtag.net/knoppix/sources, unpacked it to /usr/src, and ran "make mrproper" on it. Then I copied the .config-2.6.5 file from the /boot folder to the kernel folder, and renamed it to .config. I then ran "make" and "make modules-install". Then, I copied the System.map and arch/i386/boot/bzImage files to /boot, renaming them to System-2.6.5.map and vmlinuz-2.6.5 respectively, overwriting the ones that were already there. When I did that I rebooted the PC, and everything ran as before. Typing "cat /proc/version" however STILL returned a 2.6.5 kernel compiled with GCC 2.whatever. So either:
1) the /proc/version file (if one exists, I think /proc was some kind of virtual folder, right?) is not updated, or
2) the system for some reason is nto using my precompiled kernel.
Any ideas what to do?
Godji
1 probably ,you have not repointing linux to your kernel
cd /usr/src && rm linux
ln -s /your kernel/ linux <----this is the problem
2 from 2.6.x up you dont need to copy bzimage...
after make oldconfig , " make install "will do (and make modules_install of course)
3 look at Makefile and see the version number,addendum...
at the beginning (you can even put extension_funny_names
so later uname -a gives "president of virtual USA" )
4 after make install ,check grub /lilo
normally with grub the make install modifies for you already
pointing link to new vmlinuz and systemmap
just reboot and cross fingers
I fugred out where the problem was. In fact, for some reason the recompilation STILL used gcc 2.whatever, although the default version was 3.3.3. I deleted gcc 2.whatever and symlinked the name of the executable to point to the new gcc. This did it, and now it says what it's supposed to - that it was compiled with GCC 3.3.3. Thanks everyone for the help!
Godji
P.S. Now at startup I get a few modules complaining and not being able to start due to the alternative gcc version that has compiled the kernel. I did "make modules-install" of course so I don't know why that happens. But it's not that I care.
The modules are stored in miniroot.gz.. so you have to put them there.. it's in the custom kernel howtoOriginally Posted by Godji
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$95.00
New Precision DWDM SFP+ 10G 80km Tunable Transceiver 50GHz C-Temp DWDM-SFP10G-C
$90.00
Lot (10) Dell 0N8TDR 850nm SFP-10G-SR-85C 10Gbs sfp+ FTLX8574D3BNL-FC N8TDR NEW
$68.00
ProLabs 10GBase-TX SFP+ RJ-45 Copper Transceiver Module P/N: SFP-10GBASE-T-C NEW
$34.99
Original CISCO SFP-10G-SR V03 10-2415-03 850nm 10GBASE-SR SFP+ Multi mode Module
$6.80
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$10.99
Lot of 10 - HP 10Gb SR SFP+ Transceiver 455883-B21 455885-001 456096-001 850nm
$25.99
CISCO SFP-10G-LR SFP TRANSCEIVER MODULE GBIC 10G 10GB SFP - 1 Year Warranty
$39.99
New Sealed Cisco GLC-TE 1000BASE-T RJ45 SFP Transceiver module *US Shipping*
$20.00
Cisco Nexus 96-Port 10G SFP+ Switch N9K-93128TX w/ 9K-M12PQ 12-Port 40G QSFP
$149.99