i have the same type of problems with my card.... it wont allow me to set essid and wep key. i am able to actuly get it working with out encrpytion but that is not what i want at all
I'm trying to get wireless working on Linux.
I've a Intel 2100 built in Wireless and i think it's supported on this linux version.
I've executed wavelan and setup all as i do on windows. (SSID, WEP)
Any help aviable to one that doesn't know how possible can this work ???
I would preciate a step by step as i am starting using linux.
There is any app to activate or deactivate the wlan ???
is wep encrypted and the ssid bradcast is disable.
I tried this:
Code:iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 00:0D:88:99:47:D5 ESSID:"" Mode:Master Frequency:2.437 GHz (Channel 6) Bit Rate:1 Mb/s Bit Rate:2 Mb/s Bit Rate:5.5 Mb/s Bit Rate:11 Mb/s Bit Rate:22 Mb/s Quality=65/100 Signal level=-33 dBm Noise level=-98 dBm Encryption key:on iwconfig eth1 eth1 IEEE 802.11b ESSID:"" Nickname:"ipw2100" Mode:Managed Frequency:2.412 GHz Access Point: 00:00:00:00:00:00 Bit Rate=0 kb/s Tx-Power=32 dBm Retry:on RTS thr=2304 B Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:158 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0Code:iwconfig eth1 essid <myessid> iwconfig eth1 eth1 IEEE 802.11b ESSID:"" Nickname:"ipw2100" Mode:Managed Frequency:2.412 GHz Access Point: 00:00:00:00:00:00 Bit Rate=0 kb/s Tx-Power=32 dBm Retry:on RTS thr=2304 B Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:158 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I think the problem is on essid and wep
Any help ?
i have the same type of problems with my card.... it wont allow me to set essid and wep key. i am able to actuly get it working with out encrpytion but that is not what i want at all
At least you got Knoppix to detect your wirless card. I can't get knoppix to detect my wireless. I can lwconfig, ndiswrapper, etc. but no luck. It doesn't even see it at the start up. How did you get it to work? any help would be appreciated.
1TB/2TB USB 3.0 Flash Drive Thumb U Disk Memory Stick Pen PC Laptop Storage lot
$80.39
Type C USB 3.0 Flash Drive Thumb Drive Memory Stick for PC Laptop 1TB 2TB lot
$73.29
Samsung - 990 980 970 PRO & EVO 4TB 2TB 1 TB Internal PCle Gen 4x4 NVMe M.2SSD
$320.00
Western Digital 1TB WD Blue SA510 SATA SSD Internal 2.5”/7mm Cased - WDS100T3B0A
$79.99
WESTERN DIGITAL WD BLUE 3D NAND 1TB SSD SATA 2.5" WDS100T2B0A
$35.00
WD - Blue SN580 1TB Internal SSD PCIe Gen 4 x4 NVMe
$64.99
CISCO A03-D1TBSATA 1TB 7.2K 6G 2.5INCH SATA HDD
$9.00
1TB HDD/SSD 2.5" SATA Hard Drive for Laptop with Win 10/Win 11 Pro Pre-installed
$28.99
Seagate ST1000DX001 1TB 3.5" Desktop Hybrid SSHD Solid-State Hybrid Drive
$37.50
Samsung 1TB 850 EVO 2.5" SATA Solid State Drive MZ7LE1T0 ** READ **
$48.99