Check out this link.Originally Posted by Gregwithoneg
http://www.freenet.org.nz/misc/knoppix-install.html
Paul
Myself and my learned friend have embarked on a mission to try out Linux, and we have to say how significant Knoppix is as an addition to the catalogue of Opertaing Systems.
Just one question however, of many.
How does one install Knoppix to the systems Hard Drive?
If possible, can it be setup to dual boot.
Thats two questions soz.
Check out this link.Originally Posted by Gregwithoneg
http://www.freenet.org.nz/misc/knoppix-install.html
Paul
Buy the way it is possible to dual boot.
Check out the doc's section of this site
paul
There is a guide here and a search of the forum will provide you with many of the answers you will need.
Whenever I have installed with Knoppix, the hdinstall script has automatically configured lilo to be able to boot operating systems on other partitions. I think this was broken in some previous versions of the hdinstall script, but I believe that it has been fixed for some time now.
As the heading suggests, we have succesfully installed, although not without problems.
First thing is that we now cannot see our hard drives except the partition that knoppix is on.
We cannot connect to the Internet via broadband.
We did however get a connection the first time we rebooted Linux but none since. It hangs when trying to configure the eth0 and then fails.
We are using an AEI fast ethernet adaptor.
Hope someone has a suggestion.
I am GregwithoneG's associate. I am posting immediately after G's post because whoever reads this might be suprised to learn that we have just done the first Linux boot this morning (UK Time) and guess what? We have net!
No idea whats going on here . I simply used Scroll/Lock to monitor the boot up and there was no mention of initializing the eth0.. (What we could see at least)
G has informed me that when he is in Linux (and searching for clues) he found a usb viewer under applications/tools and he sees this message-:
cannot open the file /proc/bus/usb/devices
Verify that you have usb compiled into your kernel,
have the usb modules loaded/ and haven the usbdevfs filesystem mounted.
In fact I copied it word for word as it appears right now. Yet I have access. I know I shouldn't complain cos we now have access, but the problem is that we have no idea if we are going to have access each boot.
Has anyone any suggestions?
Cisco Meraki MA-SFP-10GB-SR 10G SFP+ SR 850nm 300m LC MMF
$29.99
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Cisco Meraki MA-SFP-10GB-LR 10G SFP+ LR 1310nm 10km LC SMF
$39.99
Cisco w/ Green Hologram SFP-10/25G-LR-S 10/25GBASE-LR SFP28 Transceiver Module
$79.99
NEW FS SFP-10G-T 10GBASE T SFP+ 30M Transceiver Module (Lot of 1)
$39.95
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
SFP-10G-SR Original Cisco 10GBASE-SR SFP+ V02 Multi mode Transceiver 10-2415-02
$5.00
Genuine Cisco GLC-TE 30-1475-01 V01 1000BASE-T SFP COPPER RJ-45 100M TRANSCEIVER
$11.90
New Cisco w/ Green Hologram SFP-25G-SR-S 25G SFP28 SR 850nm 300m LC MMF Module
$69.99
New Cisco w/ Green Hologram SFP-10G-LR-S 10G SFP+ LR 1310nm 10km SMF LC Module
$34.99