-
Has enyone gotten 6.2.1 past the boot screen?
I have tried to get the live cd to boot to 4 different PC/Laptops and the furthest I got was the boot screen loading the snd drivers. But it stops at different places for each PC.
-
Originally Posted by
Chesterton
I have tried to get the live cd to boot to 4 different PC/Laptops and the furthest I got was the boot screen loading the snd drivers. But it stops at different places for each PC.
Yes, Knoppix 6.2.1 is a working version! This is almost certainly caused by a bad disk - burning software seems to malfunction regularly, based on widespread reports of difficulty. It can also be caused by a bad download - did you check the md5 sum to see if there was a good ISO file to burn? Also, since you're getting it to boot, you can try one of these at the boot prompt (big penguin onscreen):
Code:
knoppix testcd
or
knoppix testdvd
There are a number of recommendations on how to correct this, including using slower burn speed, and (assuming you use Windows to do the burning) killing the Explorer process before you burn as described here. You must have a good ISO, and the burning has to produce a disk that will pass the self-test; the results you've had leave little room for doubt that at least one of those conditions has not been met.
Hope that helps!
Krishna
-
Senior Member
registered user
I think it has something to do with knoppix not cleaning the configuration files properly on exit. On my instalation whenever I boot on another PC, I have to manually clean fstab after boot and then issue the rebuildfstab command to regenerate proper fstab config for the drives in the new PC. May be this happens with some other configuration files too. I had no problems with xorg.conf so far or anything else, but it is a possibility
-
Originally Posted by
mecho
I think it has something to do with knoppix not cleaning the configuration files properly on exit. On my instalation whenever I boot on another PC, I have to manually clean fstab after boot and then issue the rebuildfstab command to regenerate proper fstab config for the drives in the new PC. May be this happens with some other configuration files too. I had no problems with xorg.conf so far or anything else, but it is a possibility
I have to disagree. My reading of this report is that this is a new user, trying to get a CD to boot. Also, any file corruption would be from a badly burned CD, or bad download, absent a persistent store, which I don't believe has been created yet in this case.
Cheers!
Krishna
-
Senior Member
registered user
Yes, you are right. I did not pay attention to the fact that it is Live CD not USB with persistent image.
-
OK, thanks. I'll try a new burn. I did md5 it and got a matching number. I used InfraRecorder to burn the image. I'll slow down the burn or try to burn using a different PC.
Thanks again!
-
Thanks for the help. As stated, it checked out with md5, so the dl was good. I ran the burn at 1.7x and got a good copy.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Juniper EX 4300 EX4300-48P Gigabit Network Switch JunOS 21.4R3-S7 48 Port PoE
$249.00
Juniper Networks EX3300 EX3300-48P PoE+ 48-Port 4x SFP Gigabyte Ethernet Switch
$59.99
Juniper EX3300-48P 48-Port 10/100/1000BASE-T (48 PoE+ ports) with 4 SFP+
$74.00
JUNIPER EX3400-48P 48x 1GB PoE+ RJ-45 4x 10GB SFP+ 2x 40GB QSFP+, DUAL AC POWER
$168.00
Juniper Networks EX2300-C-12T Compact 12-Port EX2300-C Series Ethernet Switch
$300.00
Juniper EX4200-48PX 48-PORT 10/100/1000BASET PoE Ethernet Switch
$50.00
Juniper 48-Port GbE 8-Port PoE & 4-Port SFP Managed Network Switch EX4200-48T
$31.19
Juniper EX2200-C-12P-2G 12-Port PoE+ Compact Managed Switch
$69.99
Juniper Networks EX3400-48T 48 Port Gigabit 4 SFP 1/10G Network Switch #73
$199.99
Juniper Networks SRX100 Services Security Appliance Part Number: SRX100H2
$22.50