Can you give the results of running the following commands:
ifconfig -a
iwconfig
lsmod
Hi,
I am desperate. I tried to get a wireless Ad-Hoc connection with WinXP sp1 and my two laptops for 2 days now. It did not work. So I switchet to knoppix. Any better here either. I searched for all the information I could find on the Internet and this board. I configured my Orinoco Gold cards with wlcarconfig, asigned static ips, checked the signals with wavemon. The cards keep sending signals (tx in wavemon) but there is no rx. They keep blinking, it makes me real nervous.
So I think the cards seem to work correctly, but they do not connect. What in hell am I doing wrong? Does anybody have a solution for my problem? I really need this wireless connection.
Thanks for every response, fluppel
Can you give the results of running the following commands:
ifconfig -a
iwconfig
lsmod
I am running a Thinkpad 380XD with a Dell Truemobile 1150 wlan card (its a rebadged Orinoco Gold).
All I can get it to do is flash its lights. the Knoppix (and Kanotix too) wlancard config utils says "No Card Detected", usually (I was able to get it to go through after running wlan-ng from /etc/pcmcia/). On boot it modprobes orinoco, orinoco_cs and hermes. lsmod shows those as being in. Ifconfig -a shows eth0 as being there with no IP, no packets sent or recieved (or even dropped) but a slew of errors under tx. iwconfig shows it as being there, seemingly ok except the access point being 44:44:44:44:44:44 (which seems odd to me). I'd copy and paste it, but I'm not on that machine now (since that one doesnt have net or lan access currently.
Check lsmod again and see if there is a 1 next to orinoco_cs. Also, what are the errors under tx. And, under iwconfig does it show your card in managed mode?
Its in managed mode, and orinoco_cs has a 1. As far as the errors, I have no clue. Relative Linux newbie with zero wlan experience. when I get home and I plug into my home network, I'll post the logs I have of iwconfig, ifconfig, lsmod, and lspci (borrowing a computer at the moment since I am not near where I live, was out of town for a court hearing).
These I got from running off cd, cause the version of Knoppix I have puked some error about the drivers being compiled with version 15 while the utility was compiled with version 16.
root@ttyp0[pcmcia]# lsmod
Module Size Used by Not tainted
autofs4 9204 1 (autoclean)
serial 47044 0 (autoclean)
usb-uhci 22672 0 (unused)
usbcore 59788 1 [usb-uhci]
af_packet 14184 2 (autoclean)
orinoco_cs 4756 1
orinoco 39612 0 [orinoco_cs]
hermes 6000 0 [orinoco_cs orinoco]
ds 6452 2 [orinoco_cs]
yenta_socket 10080 2
pcmcia_core 42048 0 [orinoco_cs ds yenta_socket]
apm 10220 2
rtc 7272 0 (autoclean)
cloop 9348 2
root@ttyp0[pcmcia]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:02:2D:A9:B7:A6
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:1101 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2330 (2.2 KiB) TX bytes:0 (0.0 b)
Interrupt:3 Base address:0x100
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:76 errors:0 dropped:0 overruns:0 frame:0
TX packets:76 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4824 (4.7 KiB) TX bytes:4824 (4.7 KiB)
root@ttyp0[pcmcia]# iwconfig
lo no wireless extensions.
eth0 IEEE 802.11-DS ESSID:"NETGEAR" Nickname:"HERMES I"
Mode:Managed Frequency:2.462GHz Access Point: 44:44:44:44:44:44
Bit Rate:2Mb/s Tx-Power=15 dBm Sensitivity:1/3
Retry limit:4 RTS thrff Fragment thrff
Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX
Power Managementff
Link Quality:0/92 Signal level:134/153 Noise level:134/153
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
It looks like you have your card properly configured but it's not seeing your AP, and your laptop is not getting a dhcp assigned IP address.
Do you have a router/AP and is it configured for dhcp? If not, what kind of setup do you have.
One more thing, it looks like you are using channel 12. Did you buy this card outside the US? You may have to change that if it's not compatible with your AP.
Forget that last post. I'm looking at the wrong table.
Sorry.
Its a router/AP, and as far as dhcp config, I am not sure. Its not my AP.
As far as specs, its a Netgear MR814 v2 router.
HP ProLiant DL380 Gen9 8SFF Server - E5-2698 v3 - 32Cores - 128GB Ram - 1TB HDD
$299.00
Dell Poweredge R730xd 3.5 2x E5-2690 v3 2.6ghz 64gb H730 14x Trays 2x 1100w
$489.99
Dell PowerEdge R710 2.5" 2U Server 2x X5670 2.93GHZ 12-Core 128gb 2x 1TB SAS
$214.99
Dell Poweredge R520 2x Xeon E5-2470 v2 2.4GHz 20-Core 192gb 8xTray H710 2x750w
$344.99
Dell PowerEdge R620 Server 2x E5-2660 v2 2.2GHz 20 Cores 256GB RAM 1x 480GB SSD
$139.99
HPE Proliant DL360 Gen9 1x Xeon E5-2620 V4 2.10GHZ 32GB DDR4-2133MHZ 2x 500W PSU
$100.95
24 Cores 2.6Ghz 32GB DDR4 Dell PowerEdge R730 Server H730 Raid Card 2x 1GB RJ45
$274.00
Dell Poweredge R210 II Server Xeon E3-1220 v2 3.1ghz Quad Core / NoRam / 1x Tray
$69.99
IBM Power S822 8284-22A 12SFF Power8 3.89GHz 6Core 64GB RAM No HDD Server System
$359.99
HP ProLiant DL360p G8 Server 2x E5-2690 2.9GHz 16-Cores / 192GB / P420 / 2x 750w
$189.99