-
Junior Member
registered user
help me with the wireless LAN on Acer 5300
Hello,
Can anyone help me set up the BCM4318 wireless LAN? ndiswrapper doesnot work. I used fwcutter and modprobe to install. lsmod shows the following information:
bcm43xx 417768 0
firmware_class 11648 2 bcm43xx,pcmcia
ieee80211softmac 27008 1 bcm43xx
ieee80211 33864 2 bcm43xx,ieee80211softmac
And KWiF manage gives the green signal. But the wireless light never comes up. Then i configured the network using DHCP and it failed. I have no idea what I should do? Thanks for any suggestions.
-
Senior Member
registered user
I believe ndiswrapper is broken on 5.0.1
[ I put a much simpler fix for this in the thread Problem with BCM4318 wireless LAN on Acer 5300 ]
(I could be wrong, but getting an updated version worked for me.)
To make things more complicated, there is also a kernel driver for your chip, bcm43xx.
So when knoppix boots up, that driver loads. It does not support WEP yet (as delivered on 5.0.1 but may by now in later versions). The bcm43xx driver also gave me an error msg about missing some firmware.
remove the kernel driver
rmmod bcm43xx
Install these 2 upgrades.
ndiswrapper-common_1.23-1_all.deb
ndiswrapper-utils-1.8_1.23-1_i386.deb
ndiswrapper -m
modprobe ndiswrapper
then
wlcardconfig and netcardconfig should set things up.
best,
john
-
Junior Member
registered user
not working
Thanks johnrw. I followed your instructions but it did not work.
I rmmod the kernel driver, updated the two ndiswrapper packages and reconfigure the wireless network. The wireless light still did not come up. What's more, the wireless netcard was not found when I used dhcp to configure the network. It showed:
Sending DHCP broadcast from device eth0SIOCSIFFLAGS: No such file or directory
Operation failed.
Failed.
Hit return to exit
Then I checked with lsmod. It said:
bcm43xx 417768 0
firmware_class 11648 2 pcmcia,bcm43xx
ieee80211softmac 27008 1 bcm43xx
ieee80211 33864 2 bcm43xx,ieee80211softmac
usbcore 109084 6 usb_storage,uhci_hcd,usbhid,ehci_hcd,ohci_hcd
I was totally confused about this. Could give me some more suggestion?
-
Junior Member
registered user
not working
I solved the problem of not finding the netcard by putting bcm43xx in the blacklist. But the wireless light still refused to come up.
#ndiswrapper -l
Installed drivers:
bcmwl5 driver installed, hardware present
#dmesg | grep bcm43xx
bcm43xx driver
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev:
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
#lsmod | grep bcm43xx
(got nothing)
Can you give me some suggestion on this problem? Thanks.
-
Re: help me with the wireless LAN on Acer 5300
Originally Posted by
Pythonschlange
Hello,
Can anyone help me set up the BCM4318 wireless LAN? ndiswrapper doesnot work. I used fwcutter and modprobe to install. lsmod shows the following information:
bcm43xx 417768 0
firmware_class 11648 2 bcm43xx,pcmcia
ieee80211softmac 27008 1 bcm43xx
ieee80211 33864 2 bcm43xx,ieee80211softmac
And KWiF manage gives the green signal. But the wireless light never comes up. Then i configured the network using DHCP and it failed. I have no idea what I should do? Thanks for any suggestions.
Have you already solved the problem? I could handle the issue of configuring wireless card only using the DVD. Booting from CD I couldn't enable my wireless card either. So, if the the matter is still of any interes for you, let me know and I'll give you some suggestions. RGDS
-
Junior Member
registered user
I need your help
Hi hotumattua,
I have not solved the problem till now. Actually I installed Knoppix5.01 live on DVD on my HD. Please post some suggestioins. Thank you very much.
-
Senior Member
registered user
2 things that I found broken when trying 2 use the kernel driver bcm43xx.
1. If your router has wep, wpa, wpa2 enabled... you won't be able to use this driver.
2. dhcp, this is really important for wireless.
What security settings is your wireless router using?
Here is what bcm43xx looks like when working (in dmesg)
bcm43xx driver
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
bcm43xx: Chip ID 0x4306, rev 0x2
bcm43xx: Number of cores: 6
bcm43xx: Core 0: ID 0x800, rev 0x2, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x4, vendor 0x4243, enabled
bcm43xx: Core 2: ID 0x80d, rev 0x1, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x807, rev 0x1, vendor 0x4243, disabled
bcm43xx: Core 4: ID 0x804, rev 0x7, vendor 0x4243, enabled
bcm43xx: Core 5: ID 0x812, rev 0x4, vendor 0x4243, disabled
bcm43xx: Ignoring additional 802.11 core.
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 1, Type 2, Revision 1
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
When you get the firmware part of this right...
it will look something close to that just above...
(Note: bcm43xx: Number of cores: 6)
There is still more to do once the firmware is correct.
Is yours correctly installed yet?
-
Re: I need your help
Originally Posted by
Pythonschlange
Hi hotumattua,
I have not solved the problem till now. Actually I installed Knoppix5.01 live on DVD on my HD. Please post some suggestioins. Thank you very much.
Hi,
I made a description of how did I solved this problem to the following address:
http://www.knoppix.net/forum/posting...quote&p=107836
I hope it will work in your case too.
Hotu Mattua
-
Junior Member
registered user
to johnrw
I uninstalled the bcm43xx and reinstalled it with bcm43xx-fwcutter.
lsmod | grep bcm43xx
bcm43xx 417768 0
ieee80211softmac 27008 1 bcm43xx
ieee80211 33864 2 bcm43xx,ieee80211softmac
firmware_class 11648 2 bcm43xx,pcmcia
This looks normal, right?
dmeg | grep bcm43xx show some errors.
bcm43xx driver
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev:
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
bcm43xx driver
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, enabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev:
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 0/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 0/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 0/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 0/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 1/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
Can you get some clues from this information?
I used cable connection to the internet. Security setting is wap. But this is not a problem. I can switch to wep if my wireless card can work.
thanks.[/quote]
-
Junior Member
registered user
to hotumattua
thanks for your suggestion. I can enable the wireless card in system/networking, but I could not activate it. In the control center, I could not even enable it. Do you know what's the problem with my machine? thanks.
Similar Threads
-
By keeper in forum Laptops
Replies: 13
Last Post: 02-12-2009, 11:58 PM
-
By kakabach in forum Networking
Replies: 2
Last Post: 09-30-2006, 10:30 AM
-
By Pythonschlange in forum Networking
Replies: 8
Last Post: 09-22-2006, 11:52 AM
-
By PatrickT in forum Laptops
Replies: 0
Last Post: 06-25-2006, 03:19 AM
-
By atomicbluefish in forum Networking
Replies: 0
Last Post: 02-09-2006, 09:07 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
1TB/2TB USB 3.0 Flash Drive Thumb U Disk Memory Stick Pen PC Laptop Storage lot
$580.99
Type C USB 3.0 Flash Drive Thumb Drive Memory Stick for PC Laptop 1TB 2TB lot
$73.29
Netac 1TB 2TB 512GB Internal SSD 2.5'' SATA III 6Gb/s Solid State Drive lot
$109.99
Seagate Laptop SSHD 1TB ST1000LM014 8GB NAND Flash 2.5" Solid Sata Hybrid Drive
$25.99
1TB Samsung 850 Pro Series 2.5" SATA 3 SSD MZ-7KE1T0BW HDD hard drive MZ-7KE1T0
$59.99
Seagate Barracuda ST1000DM003 1 TB SATA III 3.5 in Desktop Hard Drive
$14.99
1TB HDD/SSD 2.5" SATA Hard Drive for Laptop with Win 10/Win 11 Pro Pre-installed
$18.57
Samsung - Geek Squad Certified Refurbished 870 EVO 1TB SATA Solid State Drive
$67.99
Fanxiang 4TB 2TB 1TB SSD 550MB/s 2.5'' SATA III Internal Solid State Drive lot
$209.99
1TB 2TB Type C USB 3.0 Flash Drive Thumb Drive Memory Stick for PC Laptop New
$9.99