5.0 and 5.0.1 misconfigures network card?

Printable View

Show 40 post(s) from this thread on one page

06-29-2006, 12:51 PM
skydan

5.0 and 5.0.1 misconfigures network card?

Knoppix 5.x is failing to set up the network connection on one of my machines here.
Networking works with 3.3, 3.7, 3.9 and 4.0 (LinuxTAG DVD).

Machine is BX based motherboard (ATC-6220), PII/400, 256Mb. NIC is 3com 3c900B.
DHCP served by firewall (Smoothwall 2.0) connected to DLink 604T. Various other
machines on network running Debian. They can ping each other and use the Internet
and everything, so it's not that before you ask.

With netcardconfig I can configure an IP address for eth0 but it the card is non reponsive
(cannot ping other machines and they cannot ping it). It shows up in ifconfig though.

vortex_diag (from Donald Becker's site) shows the card is using the correct ethernet
port (it's a combo card).

Running "ispci -v" shows knoppix has detected network card. It looks normal.
Base address=0x6800 which it has always been in w9x and previous knoppixs (knoppixen?).

Running "ifconfig -a" shows eth0 as a detected interface but base address is something
else. In fact it shows a different address everytime it boots. So far I've had 0x2000,
0x6000, 0x8000, 0xc000, 0xe000 from both 5.0 DVD and 5.0.1 CD.

I believe this is why it's not working? It's something new in 5.0 as 3.x and 4.0 worked.

On another note, the soundcard is fanally working! It never work pre-5.0. The card is
Soundmonster II (AU8830). It's always been detected on the boot screen, just never
worked from KDE. Might this even be related to the network card problem?
(Now I think about it I should go back and check its base address?)

I'm still learning about device configuration stuff so this is about as far as I can go.
Is this a bug in 5.0?
Is there a way to set the base address manually or otherwise get it working?

Oh, I have another similar machine, also BX base (AX6B+) PIII/800. Also 3c900B NIC
but Radeon QD and SBLive (vs Elsa Erazor III and SM2). The on-board SCSI confounds
SuSE Live DVDs and various disk utils, but the 5.0 DVD and 5.0.1 CD work flawlessly on it.
The mystery deepens. Any ideas?

Thanks.
07-03-2006, 05:20 PM
Zrebel

This sounds like a post for the Networking forum, but I will try to help anyways. What is the info returned from ifconfig? Can you ping 127.0.0.1 ? does the IP address you get look like the addresses of the other machines on your network? i.e. knoppixbox has 192.168.0.5 and the others are like 192.168.0.2 or 192.168.0.23. If knoppixbox is 192.168.0.2 and others are 192.164... then they cannot talk because you are on wrong subnet. (the exact numbers are irrelevent. the first, second or(inclusive) third numbers must be the same depending on what class of address your network is using.
07-11-2006, 05:51 PM
skydan

Thanks for the reply. I wondered whether it was networking or booting but I thing it's a boot config problem hence this forum. I didn't try loopback. I'll try it now... Ping to loopback ok.

I understand IP addrs and subnet masks etc. So, no. It's not the choice of IP addr. (FYI the network uses 192.168.7.xx and separates it from the red side of the firewall which is 192.168.1.xx). Knoppix boot up shows it detected eth0 and was dhcp'ing in the background as normal. Running ifconfig, however, didn't display eth0. "ifconfig -a" showed eth0 but not configuraed with an IP addr. In case DHCP failed for some reason I can manually configure eth0. But it was unresponsive. The base address (io addr whatever) shown by ifconfig differed from the base addr shown by "lspci -v". I know the value from lspci was the correct one and ifconfig was incorrect. In fact, on every reboot the ifconfig one changed (see original post). I didn't capture the output of lspci and ifconfig (no network and would mean finding a floopy) and thought I could explain it well enough.

Anyway here is the output of various commands so you can see if you concur with my diagnosis:

lspci -v

shows io port of ethernet controller is 0x6800 (highlighted with >>>)

Code:

0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) Flags: bus master, medium devsel, latency 64 Memory at e0000000 (32-bit, prefetchable) [size=128M] Capabilities: [a0] AGP version 1.0 0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: de000000-dfffffff Prefetchable memory behind bridge: ae000000-afffffff 0000:00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02) Flags: bus master, medium devsel, latency 0 0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master]) Flags: bus master, medium devsel, latency 64 I/O ports at f000 [size=16] 0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI]) Flags: medium devsel I/O ports at 6400 [size=32] 0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02) Flags: medium devsel, IRQ 9 0000:00:0b.0 Ethernet controller: 3Com Corporation 3c900B-TPC Etherlink XL [Cyclone] (rev 04) Subsystem: 3Com Corporation 3c900B-TPC Etherlink XL [Cyclone] Flags: bus master, medium devsel, latency 64, IRQ 11 >>> I/O ports at 6800 [size=128] Memory at e8040000 (32-bit, non-prefetchable) [size=128] Expansion ROM at 20000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 1 0000:00:0c.0 Multimedia audio controller: Aureal Semiconductor Vortex 2 (rev fe) Subsystem: Diamond Multimedia Systems Monster Sound II Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at e8000000 (32-bit, non-prefetchable) [size=256K] I/O ports at 6c00 [size=8] I/O ports at 7000 [size=8] Capabilities: [dc] Power Management version 1 0000:01:00.0 VGA compatible controller: nVidia Corporation NV5 [RIVA TNT2/TNT2 Pro] (rev 11) (prog-if 00 [VGA]) Subsystem: Elsa AG Erazor III Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 9 Memory at de000000 (32-bit, non-prefetchable) [size=16M] Memory at ae000000 (32-bit, prefetchable) [size=32M] Expansion ROM at df000000 [disabled] [size=64K] Capabilities: [60] Power Management version 1 Capabilities: [44] AGP version 2.0

ifconfig -a

shows base addr (io port) of eth0 is 0xc000 (highlighted with >>>)

Code:

eth0 Link encap:Ethernet HWaddr 00:10:5A:F7:2C:9B BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:342 (342.0 b) >>> Interrupt:11 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:100 (100.0 b) TX bytes:100 (100.0 b)

lsmod

shows correct driver module is loaded (3c59x)

Code:

Module Size Used by af_packet 24584 0 dm_mod 50328 0 fuse 35088 0 capability 7176 0 commoncap 9088 1 capability snd_au8830 58912 0 joydev 11840 0 gameport 15240 2 snd_au8830 snd_ac97_codec 87712 1 snd_au8830 snd_pcm_oss 49696 0 snd_mixer_oss 18432 1 snd_pcm_oss snd_pcm 77572 3 snd_au8830,snd_ac97_codec,snd_pcm_oss parport_pc 39108 0 parport 33736 1 parport_pc 8250_pnp 12416 0 8250 47348 1 8250_pnp serial_core 20864 1 8250 snd_timer 23684 1 snd_pcm snd_page_alloc 11912 1 snd_pcm snd_ac97_bus 5888 1 snd_ac97_codec snd_mpu401_uart 9728 1 snd_au8830 snd_rawmidi 23328 1 snd_mpu401_uart snd_seq_device 10636 1 snd_rawmidi snd 46692 9 snd_au8830,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device intel_agp 22556 1 agpgart 31056 1 intel_agp i2c_piix4 11664 0 i2c_core 20736 1 i2c_piix4 shpchp 43360 0 pci_hotplug 27460 1 shpchp 3c59x 44200 0 mii 8448 1 3c59x soundcore 11360 1 snd evdev 11392 0 usbhid 47584 0 pcmcia 34476 0 firmware_class 11776 1 pcmcia yenta_socket 26764 0 rsrc_nonstatic 14464 1 yenta_socket pcmcia_core 37528 3 pcmcia,yenta_socket,rsrc_nonstatic apm 21996 1 unionfs 62108 1 cloop 19872 2 sbp2 24452 0 ohci1394 33716 0 ieee1394 288216 2 sbp2,ohci1394 usb_storage 70848 0 ohci_hcd 22020 0 uhci_hcd 32912 0 ehci_hcd 33160 0 usbcore 111492 6 usbhid,usb_storage,ohci_hcd,uhci_hcd,ehci_hcd

cat /proc/ioports

I looked around some more and found that /proc/ioports looked malformed? It's different from the one Debian (sarge) shows.
It looks like header lines are missing/malformed.

Code:

0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-006f : keyboard 0070-0077 : rtc 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 02f8-02ff : serial 0320-0323 : ter_protocol 0350-0353 : ter_protocol 0376-0376 : ide1 03bc-03be : parport0 03c0-03df : vesafb 03f2-03f5 : floppy 03f6-03f6 : ide0 03f7-03f7 : floppy DIR 03f8-03ff : serial 0cf8-0cff : PCI conf1 4000-403f : 0000:00:07.3 5000-500f : 0000:00:07.3 5000-5007 : piix4_smbus 6400-641f : 0000:00:07.2 6800-687f : 0000:00:0b.0 6c00-6c07 : 0000:00:0c.0 6c00-6c07 : au8830 7000-7007 : 0000:00:0c.0 7000-7007 : au8830 e000-efff : PCI Bus #01 f000-f00f : 0000:00:07.1 f000-f007 : ide0 f008-f00f : ide1

So, is this a knoppix configuration bug? And any way around it?
07-16-2006, 09:03 PM
Zrebel

'ifconfig eth0 io_addr' address

will set the start address of IO space, have you tried that to match the values? seems odd problem, I will watch for changes on my system after next reboot.
07-17-2006, 07:59 PM
skydan

Thanks. Didn't know you could do that (should read the man pages more closely).
Tried "ifconfig eth0 io_addr 0x6800" and the error "io_addr: SIOCSIFMAP: Operation not supported" came back.
Same whether knoppix or root. I figure that this error is telling me that either the module has to be compiled to accept
this command or that it is not applicable after booting has completed (more likely).

It is a strange problem, and only on this machine. Might it be a tricksy BIOS? I tried the various BIOS use/ignore cheatcode
options and none had any effect. Only with 5.x too. Though <5.0 the sound card didn't work and I feel it's part of the same
problem. Any pointers as to how Knoppix does it's config magic? Then I can delve a bit deeper and try and find the cause.
07-19-2006, 04:44 AM
Zrebel

The network card configure script is found at /etc/init.d/networking. All it does is call ifup wilth the --all option, maybe using the --force is required... hehe. It could also be a udev issue, try a 'noudev' boot.
07-20-2006, 05:02 AM
Zrebel

It turns out you can not change the IO address or IRQ for a PCI device with io_addr. I'm thinking that the option can only be used on the first ifup call during init maybe? How did noudev workout?
07-23-2006, 06:49 AM
skydan

Tried the noudev. Seemed to make things worse... NIC same as usual but now no sound and trying to start a terminal throws an error (should have written it down). Alt-F1 to the console works though.

Tried some more testing with the 5.0.1 CD on other machines. When I said that it worked on the other machines in my first post, it turns out that isn't quite true. The NIC works but the base address shown by ifconfig is incorrect. Now that I know what I'm looking for it's easy to spot! I probably checked using 3.9 and never looked further if the NIC worked on 5.0.

Anyway, I tried 5.0.1 again on the PIII BX machine and on the firewall box (K6-2, I forget the motherboard now but has VIA chipset, 2x 3com NICs). Both show incorrect base addrs from ifconfig yet the network works quite happily. There were a few quirks though (listed below). Looking through the "dmesg" output threw up an interesting result though. On <5.0 when the NIC is being configured the driver (I guess but I'm not sure what is printing this value) echoes the base address, irq etc but as a 16bit number ie 0x6800. 5.0 and 5.0.1 now display a 32bit number (clearly hex but without the 0x), with values that tie up with the address shown in ifconfig. I rebooted a few times to see how the values changed.

So, a snippet of dmesg for 5.0.1 CD on the PII machine shows:

Code:

PCI: Found IRQ 11 for device 0000:00:0b.0 3c59x: Donald Becker and others. www .scyld.com/network/vortex.html 0000:00:0b.0: 3Com PCI 3c900 Cyclone 10Mbps TPC at d0d3e000. Vers LK1.1.19

The "at d0d3e000" used to be "at 0x6800" and in this case the base address in ifconfig is 0xe000 ie the lower 16 bits of d0d3e000.

On the PIII machine (3c900B) the 32bit value shown was d0dba000. ifconfig shows a000. IO addr should be 0x6800.
NIC works, DHCP everything. Has sound. No quirks apparent.

The K6 machine has two 3com cards: eth0=3c900, eth1=3c905B.
eth0 base addr should be 0xe800. 32bit value shown is 0001e800. Was same for all reboots.
eth1 base addr should be 0xec00. 32bit value shown has been c8c90000 and c8cac000. Probably show other values for more reboots.
eth1 picked up dhcp from modem and worked normally. Manual coniguration of eth0 showed it working.
Also on this machine the boot sometimes, that is not everytime, crashes near the end. KDE throws up an error and there are no desktop icons or Konqueror window. Sound card (SB AWE64 - ok, firewall doesn't need soundcard I just couldn't be hassled removing it!) is detected but does not work. Works ok on <5.0.

You may have noticed all the machines have 3com cards so it could be a problem with the driver or something. Unfortunately they are all I have so cannot test with another NIC. But considering other quirks like desktop crashes and non-working soundcard, or now working in the case of the PII machine, makes me think it is some subtle bug in the boot/config script. I don't know what displays this value so can't say if it's in the driver or the config scripts. From a programming perspective it looks like an address is being passed rather than the value of that address but that's probably too simplistic (though typos can happen). When I get some time I'll have a look at those boot scripts you mentioned.

Here's the full dmesg output from the PII machine (the one with non-working NIC) if it helps:

Code:

Linux version 2.6.15 (root@Knoppix) (gcc version 4.0.3 20060128 (prerelease) (Debian 4.0.2-8)) #7 SMP PREEMPT Sun Feb 19 23:35:17 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000010000000 (usable) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 256MB LOWMEM available. On node 0 totalpages: 65536 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 61440 pages, LIFO batch:15 HighMem zone: 0 pages, LIFO batch:0 DMI 2.0 present. ACPI: Unable to locate RSDP Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000) Built 1 zonelists Kernel command line: ramdisk_size=100000 init=/etc/init lang=uk apm=power-off vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01342000) Initializing CPU#0 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 400.981 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 253472k/262144k available (2120k kernel code, 8128k reserved, 776k data, 296k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 803.38 BogoMIPS (lpj=1606771) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000 mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. Checking for popad bug... OK. CPU0: Intel Pentium II (Deschutes) stepping 01 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 813k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xfaf20, last bus=1 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fbae0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbb08, dseg 0xf0000 PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver SCSI subsystem initialized PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI quirk: region 4000-403f claimed by PIIX4 ACPI PCI quirk: region 5000-500f claimed by PIIX4 SMB Boot video device is 0000:01:00.0 PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0 PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: de000000-dfffffff PREFETCH window: ae000000-afffffff audit: initializing netlink socket (disabled) audit(1153631017.840:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Limiting direct PCI/PCI transfers. vesafb: framebuffer at 0xae000000, mapped to 0xd0880000, using 3072k, total 4096k vesafb: mode is 1024x768x16, linelength=2048, pages=0 vesafb: protected mode interface info at c000:042b vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 vesafb: Mode is VGA compatible Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: QUANTUM FIREBALL CR13.0A, ATA DISK drive hdb: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: YAMAHA CRW4416E, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 25429824 sectors (13020 MB) w/418KiB Cache, CHS=25228/16/63 hda: cache flushes not supported hda: hda1 hda2 < hda5 hda6 > hdb: ATAPI 32X DVD-ROM drive, 256kB Cache Uniform CD-ROM driver Revision: 3.20 hdc: ATAPI 16X CD-ROM CD-R/RW drive, 2048kB Cache libata version 1.20 loaded. mice: PS/2 mouse device common for all mice EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 4 Cannot allocate resource for EISA slot 5 Cannot allocate resource for EISA slot 6 Cannot allocate resource for EISA slot 7 EISA: Detected 0 cards. NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 196608 bytes) TCP bind hash table entries: 16384 (order: 5, 196608 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NET: Registered protocol family 1 NET: Registered protocol family 15 Using IPI No-Shortcut mode RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). input: AT Translated Set 2 keyboard as /class/input/input0 seagate: ST0x/TMC-8xx not detected. Failed initialization of WD-7000 SCSI card! usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.3 PCI: No IRQ known for interrupt pin D of device 0000:00:07.2. Please try using pci=biosirq. uhci_hcd 0000:00:07.2: Found HC with no IRQ. Check BIOS/PCI 0000:00:07.2 setup! uhci_hcd 0000:00:07.2: init 0000:00:07.2 fail, -19 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. logips2pp: Detected unknown logitech mouse model 1 ieee1394: Initialized config rom entry `ip1394' sbp2: $Rev: 1306 $ Ben Collins <[email protected]> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance input: PS/2 Logitech Mouse as /class/input/input1 Unable to identify CD-ROM format. VFS: Can't find an ext2 filesystem on dev hda. ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A cloop: Initializing cloop v2.03 cloop: loaded (max 8 devices) cloop: /cdrom/KNOPPIX/KNOPPIX: 75359 blocks, 65536 bytes/block, largest block is 65562 bytes. ISO 9660 Extensions: RRIP_1991A cloop: losetup_file: 50406 blocks, 65536 bytes/block, largest block is 65562 bytes. ISO 9660 Extensions: RRIP_1991A Registering unionfs 20060221-0341 Freeing unused kernel memory: 296k freed apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device PCI: Found IRQ 11 for device 0000:00:0b.0 3c59x: Donald Becker and others. www .scyld.com/network/vortex.html 0000:00:0b.0: 3Com PCI 3c900 Cyclone 10Mbps TPC at d0d3e000. Vers LK1.1.19 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 440BX Chipset. agpgart: AGP aperture is 128M @ 0xe0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE] PCI: Found IRQ 10 for device 0000:00:0c.0 Vortex: init.... <6>done. gameport: AU88x0 Gameport is pci0000:00:0c.0/gameport0, speed 1612kHz Capability LSM initialized fuse init (API version 7.3) device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel @redhat.com PCI: Found IRQ 11 for device 0000:00:0b.0 NET: Registered protocol family 17 NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6 over IPv4 tunneling driver vortex: IRQ fifo error
07-23-2006, 01:44 PM
skydan

Tried noudev again on the PII machine and had the desktop crash again with signal 6 (SIGABRT). just before knoppix finishes booting. Last time was on K6 machine. Was testing "noudev" at the time but don't feel it's connected. Looking at /home/knoppix/Desktop shows the files used for the icons, just no icons shown. Rebooted and tried noudev again and no crash. With noudev and attempting to open terminal window says it is unable to open a PTY etc.

Here is the traceback of the desktop crash if it is useful: (or should this be sent to the knoppix bug list?)

Code:

Using host libthread_db library "/lib/tls/libthread_db.so.1". [Thread debugging using libthread_db enabled] [New Thread -1231890752 (LWP 1825)] [KCrash handler] #5 0xb7d4e7c7 in raise () from /lib/tls/libc.so.6 #6 0xb7d5006b in abort () from /lib/tls/libc.so.6 #7 0xb7f43654 in __gnu_cxx::__verbose_terminate_handler () from /usr/lib/libstdc++.so.6 #8 0xb7f41045 in std::set_unexpected () from /usr/lib/libstdc++.so.6 #9 0xb7f41082 in std::terminate () from /usr/lib/libstdc++.so.6 #10 0xb7f411ba in __cxa_throw () from /usr/lib/libstdc++.so.6 #11 0xb7f415fb in operator new () from /usr/lib/libstdc++.so.6 #12 0xb7f416cd in operator new[] () from /usr/lib/libstdc++.so.6 #13 0xb75dfe01 in QString::setLength () from /usr/lib/libqt-mt.so.3 #14 0xb75e83e3 in operator>> () from /usr/lib/libqt-mt.so.3 #15 0xb7b1a88a in KIO::Slave::createSlave () from /usr/lib/libkio.so.4 #16 0xb7b1baa5 in KIO::Scheduler::createSlave () from /usr/lib/libkio.so.4 #17 0xb7b3f317 in KIO::Scheduler::startJobDirect () from /usr/lib/libkio.so.4 #18 0xb7b3f72c in KIO::Scheduler::startStep () from /usr/lib/libkio.so.4 #19 0xb7b3f83c in KIO::Scheduler::qt_invoke () from /usr/lib/libkio.so.4 #20 0xb72c354b in QObject::activate_signal () from /usr/lib/libqt-mt.so.3 #21 0xb72c3fdc in QObject::activate_signal () from /usr/lib/libqt-mt.so.3 #22 0xb76572ae in QTimer::timeout () from /usr/lib/libqt-mt.so.3 #23 0xb72e84a1 in QTimer::event () from /usr/lib/libqt-mt.so.3 #24 0xb725987a in QApplication::internalNotify () from /usr/lib/libqt-mt.so.3 #25 0xb7259a76 in QApplication::notify () from /usr/lib/libqt-mt.so.3 #26 0xb793002e in KApplication::notify () from /usr/lib/libkdecore.so.4 #27 0xb71eb001 in QApplication::sendEvent () from /usr/lib/libqt-mt.so.3 #28 0xb724b305 in QEventLoop::activateTimers () from /usr/lib/libqt-mt.so.3 #29 0xb71fed2a in QEventLoop::processEvents () from /usr/lib/libqt-mt.so.3 #30 0xb7272255 in QEventLoop::enterLoop () from /usr/lib/libqt-mt.so.3 #31 0xb727217a in QEventLoop::exec () from /usr/lib/libqt-mt.so.3 #32 0xb725838d in QApplication::exec () from /usr/lib/libqt-mt.so.3 #33 0xb68c112f in kdemain () from /usr/lib/libkdeinit_kdesktop.so #34 0xb7fbc524 in kdeinitmain () from /usr/lib/kde3/kdesktop.so #35 0x0804e1d6 in ?? () #36 0x00000001 in ?? () #37 0x080d03e8 in ?? () #38 0x00000001 in ?? () #39 0x00000000 in ?? ()
07-24-2006, 07:29 AM
skydan

Had a closer look at how knoppix autoconfigures the hardware using the 5.0.1 CD. Starting point was "/etc/init.d/knoppix-autoconfig" that basically does it all. The one command hwsetup does all the magic though the script shows you can specify "nohwsetup" from the boot prompt to switch to using "etc/modules" instead, whatever that is. I tried both and there was no change.

To track down exactly where the information in dmesg was coming from I tried the following:
1. booted using "knoppix emergency" from the boot prompt to get a bare system without running any scripts.
2. mount -t proc /proc /proc to mount /proc.
3. mount -o remount,rw / to remount root as read-write.
4. dmesg shows no network card information. Only loopback shown in ifconfig -a.
5. modprobe -v 3c59x fires up the driver for the NIC and echoes:

Code:

insmod /lib/modules/2.6.17/kernel/drivers/net/mii.ko insmod /lib/modules/2.6.17/kernel/drivers/net/3c59x.ko 3c59x: Donald Becker and others. www .scyld.com/network/vortex.html

6. dmesg now shows netword card information:

Code:

PCI: Found IRQ 11 for device 0000:00:0b.0 3c59x: Donald Becker and others. www .scyld.com/network/vortex.html 0000:00:0b.0: 3Com PCI 3c900 Cyclone 10Mbps TPC at d085a000. Vers LK1.1.19

and ifconfig -a shows eth0 with base address=0xa000

So the bad address would appear to be from modprobe, the 3c59x driver and/or the 2.6.17 kernel (and 2.6.15 from 5.0).
I figure that modprobe and the driver haven't changed much yet the kernel is bleeding(ish) edge? Am I correct in guessing
that the first and last lines shown in (6) are from the kernel? I'm not familiar with the intricacies of the kernel so I think this
is about as far as I can take it. Maybe a kernel hacker can expand on this a bit more.

Show 40 post(s) from this thread on one page