ACER TM250 (2) -- FYI: This is how they do it...

I am not sure if this is appropriate.
These following are the config files from the Mandrake 9.1 restore disk for ACER 250.

CPUINFO:

processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Genuine Intel(R) CPU 2.66GHz
stepping : 9
cpu MHz : 2664.432
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 5321.52

PCI devices found:
Bus 0, device 0, function 0:
Host bridge: PCI device 8086:3580 (Intel Corp.) (rev 2).
Bus 0, device 0, function 1:
System peripheral: PCI device 8086:3584 (Intel Corp.) (rev 2).
Bus 0, device 0, function 3:
System peripheral: PCI device 8086:3585 (Intel Corp.) (rev 2).
Bus 0, device 2, function 0:
VGA compatible controller: PCI device 8086:3582 (Intel Corp.) (rev 2).
IRQ 5.
Prefetchable 32 bit memory at 0xe8000000 [0xefffffff].
Non-prefetchable 32 bit memory at 0xe0000000 [0xe007ffff].
I/O at 0x1800 [0x1807].
Bus 0, device 2, function 1:
Display controller: PCI device 8086:3582 (Intel Corp.) (rev 2).
Prefetchable 32 bit memory at 0xf0000000 [0xf7ffffff].
Non-prefetchable 32 bit memory at 0xe0080000 [0xe00fffff].
Bus 0, device 29, function 0:
USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 3).
IRQ 5.
I/O at 0x1820 [0x183f].
Bus 0, device 29, function 1:
USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 3).
IRQ 11.
I/O at 0x1840 [0x185f].
Bus 0, device 29, function 2:
USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 3).
IRQ 4.
I/O at 0x1860 [0x187f].
Bus 0, device 29, function 7:
USB Controller: Intel Corp. 82801DB USB EHCI Controller (rev 3).
IRQ 10.
Non-prefetchable 32 bit memory at 0xe0100000 [0xe01003ff].
Bus 0, device 30, function 0:
PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 131).
Master Capable. No bursts. Min Gnt=4.
Bus 0, device 31, function 0:
ISA bridge: PCI device 8086:24cc (Intel Corp.) (rev 3).
Bus 0, device 31, function 1:
IDE interface: PCI device 8086:24ca (Intel Corp.) (rev 3).
IRQ 4.
I/O at 0x1810 [0x181f].
Non-prefetchable 32 bit memory at 0x20000000 [0x200003ff].
Bus 0, device 31, function 3:
SMBus: Intel Corp. 82801DB SMBus (rev 3).
IRQ 10.
I/O at 0x1880 [0x189f].
Bus 0, device 31, function 5:
Multimedia audio controller: Intel Corp. 82801DB AC'97 Audio (rev 3).
IRQ 10.
I/O at 0x1c00 [0x1cff].
I/O at 0x18c0 [0x18ff].
Non-prefetchable 32 bit memory at 0xe0100c00 [0xe0100dff].
Non-prefetchable 32 bit memory at 0xe0100800 [0xe01008ff].
Bus 0, device 31, function 6:
Modem: Intel Corp. 82801DB AC'97 Modem (rev 3).
IRQ 10.
I/O at 0x2400 [0x24ff].
I/O at 0x2000 [0x207f].
Bus 2, device 4, function 0:
CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 1).
IRQ 10.
Master Capable. Latency=168. Min Gnt=192.Max Lat=5.
Non-prefetchable 32 bit memory at 0x20001000 [0x20001fff].
Bus 2, device 4, function 1:
CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (#2) (rev 1).
IRQ 10.
Master Capable. Latency=168. Min Gnt=192.Max Lat=5.
Non-prefetchable 32 bit memory at 0x20002000 [0x20002fff].
Bus 2, device 10, function 0:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 16).
IRQ 11.
Master Capable. Latency=64. Min Gnt=32.Max Lat=64.
I/O at 0x3000 [0x30ff].
Non-prefetchable 32 bit memory at 0xe0200000 [0xe02000ff].

/etc/modules.conf

probeall scsi_hostadapter usb-storage
probeall usb-interface usb-uhci ehci-hcd
alias eth0 8139too
alias sound-slot-0 i810_audio
alias char-major-212 slmodem
alias slmodem slamrmo
options slmdm country=INDONESIA

# /etc/modules: kernel modules to load at boot time.
#
# This file should contain the names of kernel modules that are
# to be loaded at boot time, one per line. Comments begin with
# a `#', and everything on the line after them are ignored.

scsi_hostadapter

If needed I can send (by email) the kernel config file and the XF86Config file

regards,

Please send us

I have a TM242LC and it would help

Too Bad, I have already deleted it :cry:
Anyway, please see the REDHAT version at:

http://rms46.vlsm.org/1/95.html#6

as well as the Slackware one:

http://rms46.vlsm.org/1/95.html#8

Hopefully it helps...

Can you tell me how you install the slmodem driver? I'm using Knoppix 3.3 and try to install the slmodem and slamrmo in my notebook Toshiba Satellite 1805, but it doesn't work at all. It always stuck with no modem found message. slmodem module loaded with warning! See www.tux.org.
Can you tell me where I can load the driver like yours ?
Please help me ! :oops: