installed on to HD but can't boot

ive succesfully installed knoppix multiple times but when i try to boot it without the cd, lilo doesnt even run and it goes straight into windows. so i tried using a boot disk when its wirting it it gives me error messages and when i try to boot from it after installation it gives me this error message " boot failed/invalid replace disk and then press return". what in the world do i do?!!! please help me

Hi

I've had similar problems.
I had a Promise TX2 IDE card connected.
It mucks up Knoppix so bad, Lilo can't even wirte to the HD.
You probably also have some hardware device connected
which is not supported by Knoppix (or any Linux) and
goofs up everything uncontrollably and mysteriously.

Try disconnecting any PCI cards and try installing again.

Mark

You might try booting with the windows bootloader.

- Choose NO when asked to put lilo in mbr so it goes into your linux partition instead.
- copy your bootsector to a file: $dd if=/dev/hdXX of=/bootsect.lnx bs=512 count=1
(change XX to whatever your linux partition is.)
- copy the bootsect.lnx to a floppy and transfer it to C:\
- add the following line as last line to C:\boot.ini: C:\bootsect.lnx="Knoppix"

Downside is that you have to remember to do it every time you run lilo after changing it.

Quote:

---

Originally Posted by Markus

- copy your bootsector to a file: $dd if=/dev/hdXX of=/bootsect.lnx bs=512 count=1

---

i cant access my hardrive in order to do that. whenever i type that in a root console is says "bash /dev/hdb1(my linux partition) access denied" what is going on here?

Are you doing this when booted from the CD?
It won't write to the root of the CD, you have to write the output somewhere else.

Right-click the hdb1-icon on the desktop and change to read-write mode, then do:
$dd if=/dev/hdb1 of=/dev/hdb1/bootsect.lnx bs=512 count=1

You should now have a file named bootsect.lnx in your linux partition.

Now you can format a floppy with: $ mkfs.msdos /dev/fd0
Mount it with: $ mount /dev/fd0
copy over the file: $ cp /dev/hdb1/bootsect.lnx /floppy

nope same thing happens "bash: /dev/hdb1 permission denied" now what?!

I'd try another floppy.

Do a full format in KFloppy -- format it to DOS

and try again.

It would be helpful to know that those errors were.......

You didn't say if you're doing this from the live-CD.

If so, you could try:
sudo mount -t ext3 /dev/hdb1 /mnt/hdb1 (assuming it is ext3 you've chosen)
sudo chroot /mnt/hdb1
sudo dd if=/dev/hdb1 of=/dev/hdb1/bootsect.lnx bs=512 count=1

Although, you might as well try what fingers99 suggested.

everything supposedley worked fine in the root console (no errors) but bootsect.lnx didnt appear on my drive!!! and so, i couldnt write it to a floppy (how do you do that anyways?). sorry for the trouble but now what?!!! :oops: :roll: :?

How about posting your lilo.conf so we can see where it's at.
You'll find it at /mnt/hdb1/etc/lilo.conf

Did you manage to copy over the files ok when installing?
That is, does it at least write to hdb1?
Try mounting your hdb1 with:
$ mount /dev/hdb1 /mnt/hdb1
and then checking what you have mounted with:
$ mount
Hopefully you get a (rw) at the end of the line containing hdb1.
You can also try booting the CD with:
$knoppix nodma (+ other cheatcodes you usually use)

As for copying to floppy:
$ mount /mnt/floppy
$ cp /dev/hdb1/bootsect.lnx /floppy
$ umount /mnt/floppy

Just a thought, do you have some sort of virus protection on in your BIOS
preventing writing to the master boot record. Might be worth a check.