As root user, try the command:
modprobe 8139too
then try
ifconfig -a
& hopefully you will see a eth0 device.
If the eth0 device exists, try netcardconfig
Printable View
As root user, try the command:
modprobe 8139too
then try
ifconfig -a
& hopefully you will see a eth0 device.
If the eth0 device exists, try netcardconfig
Hi James,
I did as you instructed - modprobe 8139too then ifconfig -a then netcardconfig.
Here is the results:
By the way - after running ifconfig -a I still was not able to load a web page. However it seems like some signal is getting through. In other words - the browser takes a while before letting me know that it can't connect. Before running your commands when I tried using the browser it immediatly told me there was not a connection. Is this helpful?Code:eth0 Link encap:Ethernet HWaddr 00:50:FC:FE:FD:47
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:5 Base address:0xc000Hi James,
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:10 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
By the way, when I re-boot, the configuration seems to go away.
cindy, how do you go to the Internet? I have simple ADSL Ethernet modem (no router), setup as bridge and I can't go to the Internet with eth0 setup as your is. My ifconfig looks like that:
eth0 Link encap:Ethernet HWaddr 00:50:8D:66:BA:EE
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1871 errors:0 dropped:0 overruns:0 frame:0
TX packets:1842 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1587863 (1.5 MiB) TX bytes:301642 (294.5 KiB)
Interrupt:11 Base address:0x2000
(lo....., ppp0....).
I get this in diferent way in diferrent distributions of Linux - automatic or I use a dirty trick - during netcardconfiguration I use static IP adrress but delete all numbers, and conection works.
If I want to accsess my modem, for setup, I must configure net card with DHCP, 192.168.1.2
I'm using cable.
Maybe the problem is this: when I generated that output I had a wireless router between the Knoppix computer and the cable modem.
Like this:
cable modem >----- ethernet cable----- >wireless router >-----ethernet cable-----> knoppix computer.
I could connect the cable modem directly to the knoppix computer and try your commands again if you want.
My cable modem is a motorolla surfboard and my wireless router is a belkin f5d6231-4 (802.11b)
You should be able to keep the router in the circuit. You'll want to , as that will be the final way you'll run anyway. There is certainly no reason why the router should not stay in the configuration.Quote:
Originally Posted by cindy
One problem from a previous posting is that your own IP address seems to be 192.168.0.1. That is likely the IP address of your router (unless you've changed it) and can't be your address too. If it's getting set this way by an automatic Netcardconfig the I would suggest booting again from CD and seeing what your current ifconfig is, the booting the hd install again, doing the steps James gave you including the netcardconfig. If you are doing an "automatic" netcardconfig and still get the 192.168.0.1 setting, do a netcardconfig and take the manual setting option and force the IP address o be what it was when you booted from CD (and maake the other settings too). Does that help? It seems like your hard disk install is forcing the wrong IP address, but why I have no idea.
What about this http://www.knoppix.net/forum/viewtopic.php?t=19518 Please, watch the very end of the post.
James,George and "tdjokic",
Got it working! Thank you so much!!!
The problem was I answered " no" each time when netcardconfig asked "Start DHCP broadcast?"
In retrospect I know that was really dumb I know!. I apologize for wasting your time. But your advice and encouragement kept me going when I was about to give up. Thank you so much!
One more request?
Now that the card is being detected is there anything more I need to do to make sure it stays that way? Can I "save" the settings so that Knoppix will be able to detect the ethernet card next time turn on the machine?
Sorry Harry - I meant to address the message to you. I don't know where I came up with George! I've been fooling with this computer too much. I'm taking a break!