USB stick (Canyon & SanDisk)
Hello.
I am trying to connect my USB sticks on computer, but I have no luck. I have tried to run it with editing /etc/fstab (/dev/sda1 /mnt/usbstick vfat defaults, user, noauto, showexec, umask=022 0 0) but it did not want to mount.Here is info I get with kinfocenter:
Code:
Cruzer Mini
Manufacturer: SanDisk Corporation
Serial #: SNDK417DA405B1F00707
Class
0
((Defined at Interface level))
Subclass
0
Protocol
0
USB Version
2.00
Vendor ID
0x781
(SanDisk Corp.)
Product ID
0x5150
(SDCZ2 Cruzer Mini Flash Drive (thin))
Revision
0.10
Speed
480 Mbit/s
Channels
0
Max. Packet Size
0
And this is the info if I run: lsusb:
Code:
Bus 001 Device 019: ID 0781:5150 SanDisk Corp. SDCZ2 Cruzer Mini Flash Drive (thin)
Is there any way of fixing this problem?
Thank you very much!
USB stick (Canyon & SanDisk)
Your messages should include a device that the filesystem has been assigned to (usually /dev/sda1, possibly /dev/uba1 depending on your version of knoppix and how you are running it) as well as the actual bus address, unless, the boot sector of the devices is not recognized or uninitialized (no partitions or filesystems).
Please post your exact mount command and any other particulars.
USB stick (Canyon & SanDisk)
Did you unmount the filesystem before removing it?
We still do not know how or what version of knoppix you are using. Version # please as well as live or installed.
The line in fstab is meaningless as it does not refer to your referenced device and no spaces are allowed in the _options_ section.
USB stick (Canyon & SanDisk)
Well... You can't just remove part of a filesystem and not expect an error message.
All modern desktops should include the -l switch in their unmouint scripts. The -l switch detaches a filesystem and allows processes time to clean up before an error is sent.
Even so, you should be certain that no active processes are using the filesystem before you attempt an unmount. Close any open graphical file viewer and cd out of any terminal session that is in the filesystem, then issue the command; umount /mount/point -l .
similar problem please csn you help, im a biologist
hi i have just installed a live version of knoppix live which was spechally made with pre installed biology and genetics software on to my pc,, the live version has all the stuff working including usb date storage flash drive support as well as internet and otheres..
whe i managed to install, i lost the internet connection but iu found how to restore this , however i still know nothing of how to get the usb flash drive working, i plug one in and nothing happens?
i try to look at the drive by clicking on the icon and i get this message:-
Could not mount device.
The reported error was:
mount: only root can mount /dev/sda1 on /mnt/flash
any i deas?... i tryed the manual mountm but i could have got that wrong!.. i dont under sand why on the live edition it worked but after installation it stops working.. please could some body help with making by flash drive to work.
i have looked round the site i thin kthat this data may be help full
root@box:/home/user# sudo cat /etc/fstab
# /etc/fstab: filesystem table.
#
# filesystem mountpoint type options dump pass
/dev/hda1 / reiserfs defaults 0 1
proc /proc proc defaults 0 0
/dev/fd0 /floppy vfat defaults,user,noauto,showexec,umask=022 0 0
usbfs /proc/bus/usb usbfs devmode=0666 0 0
sysfs /sys sysfs defaults 0 0
tmpfs /dev/shm tmpfs defaults 0 0
/dev/cdrom /cdrom iso9660 defaults,ro,users,noexec,noauto 0 0
/dev/dvd /dvd iso9660 defaults,ro,users,noexec,noauto 0 0
/dev/sda1 /mnt/flash auto noauto,owner,kudzu 0 0
# Added by KNOPPIX
/dev/hda2 none swap defaults 0 0
root@box:/home/user#
oot@box:/home/user# sudo fdisk -l
Disk /dev/hda: 255 heads, 63 sectors, 1044 cylinders
Units = cylinders of 16065 * 512 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 662 5317483+ 83 Linux
/dev/hda2 663 917 2048287+ 82 Linux swap
root@box:/home/user#
Mount usb device fstab entry
Try:
/dev/sda1 /mnt/flash vfat noauto,users,exec,umask=000 0 0
instead of your line:
/dev/sda1 /mnt/flash auto noauto,owner,kudzu 0 0
nope that dint work either
i did as you asked, (thanks for you help by the way), i made the directory..
then i entered your mount command and i got this reply telling me how to use the mount command, but since i have all ready put the command in fstab, i dint think i need it, so io tryed to askcess the usb and i got this new error message come up:---
Could not mount device.
The reported error was:
mount: /dev/sda1 is not a valid block device
help!!
I simply dont understand why a distro that works as a live, when put onto the hard drive now magically looses things?..
Im willing to try any thing at this stage,, so please kepp the surgestions comming...
thanks every body for your time and help, its appreciated..
