-
knoppix will not boot
I get the starting screen and disabled everything with cheat codes. I also tried setting to vga. I hit enter, see a couple lines of text and the computer reboots? Anyone have any idea? I actually tried the memtest through knoppix as well. It also caused a reboot, could it be bad memory?
I computer is quite old as well, but I figured it can run linux. Its a pentium 166.
-
Junior Member
registered user
Does it meet the minimum requirements?
Intel-compatible CPU (i486 or later),
20 MB of RAM for text mode, at least 96 MB for graphics mode with KDE (at least 128 MB of RAM is recommended to use the various office products),
bootable CD-ROM drive, or a boot floppy and standard CD-ROM (IDE/ATAPI or SCSI),
standard SVGA-compatible graphics card,
serial or PS/2 standard mouse or IMPS/2-compatible USB-mouse.
-
Senior Member
registered user
i personally have a p100 and it works in textmode. not fast but... how much memory do you have? id recomend 32Mb or so as min.
-
yes, it meets the requirements. Also it has 64Mb RAM.
-
Senior Member
registered user
it might be a faulty cd.
have you checked the MD5sum?
if you have and it matches the ISO file is ok. if that doesn't match there is something wrong with the download.
have you tried the knoppix testcd function? if that goes trough it might be something else. hmmm, such old computers can have flaky BIOS batteries, not likely in theis case as it boots.
hmmm.
i guess you have to boot such an old computer with floppies, if so how did you make them. did you check them before making the bootfloppies?
-
Junior Member
registered user
It meets the minimum requirements for text mode then, not for booting into the GUI. Have you tried just booting into text mode?
-
Junior Member
registered user
cannot boot knoppix
This problem happened to me recently. I was installing Knoppix 3.6 over 3.4. the system
crashed, that is would not progress further in the loading than the first few lines. In order to correct the problem I had to clean, not format, but wipe the hard drive. I used the commercial program Tuff Test. A new install worked. I have 3 computers with some version of Knoppix/debian installed. I,also, have plug-in hard drives to allow me to change OS at my whim.
I hate to be a "Kill Joy" but I think you have to re-install.
William
Similar Threads
-
By doesnotcompute in forum Hardware & Booting
Replies: 1
Last Post: 03-01-2005, 07:29 PM
-
By helios17 in forum General Support
Replies: 7
Last Post: 11-27-2004, 06:27 AM
-
By proto in forum General Support
Replies: 3
Last Post: 03-17-2004, 11:29 PM
-
By ebone in forum Customising & Remastering
Replies: 4
Last Post: 05-16-2003, 02:26 AM
-
By mswarbrick in forum Customising & Remastering
Replies: 6
Last Post: 04-18-2003, 12:30 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules

Lot 16) Micron 16GB 1Rx4 PC4-3200AA-RC2-12 ECC DDR4 Ram MTA18ASF2G72PZ-3G2J3UI
$1200.00

SK Hynix 16 GB Registered DDR4 - HMA82GR7JJR8N-VK
$65.00

Samsung 32GBX2 1Rx4 PC4-3200AA DDR4 ECC Server Memory M393A4G40AB3-CWEBQ 64GB EC
$370.00

2 in 1 USB 3.0 Card Reader Micro TF card Reader usb adapter High Speed Cardreder
$3.99

Samsung M393A4K40BB2-CTD 32GB 2Rx4 PC4-21300 DDR4-2666 Memory Module
$184.00

Samsung 96GB LPCAMM2 PC5 9600 FE1 E1 LPDDR5X CAMM2 M561K6LC3CL1-CCV DDR5 Memory
$2150.00

USB 3.0 Flash Drive 32GB 64GB 128GB Memory Stick Thumb Stick Lot Pack
$826.09

SK Hynix 64GB PC4-2933Y Server Memory DDR4 RAM HMAA8GR7MJR4N-WM
$449.99

Samsung 32GB (1x32GB) PC4-17000 (DDR4-2133) LRDIMM Memory (M386A4G40DM0-CPB0Q)
$120.00

Micron 64GB DDR4 PC4-2666V 4DRx4 ECC LRDIMM MTA72ASS8G72LZ-2G6D2 SERVER MEM
$320.00