-
Senior Member
registered user
KnoppixCD boot with 3GB of ram...toram..experiment(success)
With 3Gb physical ram installed, I installed the Knoppix CD with:
Knoppix26 toram myconfig=scan (previous install of config)
The result was an install of the CD toram in about 4 minutes. The " system guard" reported a total of 2.21GB of free ram.
A side issue in this experiment.
I had previously set up a USB HDD of 80GB with qtparted to have 4 primary partitions, 40MB ext2, 2GB linux swap, 2GB linux swap, 4GB ext2 and the remainder free.
The effect of this HDD was to supply a total of 4GB of swap to the knoppix CD install which was reported in " system guard" along with the memory figures.
I am booted in this mode at this time with the CD removed from the computer, the "C" drive powered down, the floppy drive powered down, and only one USB HDD powered up (external).
The 4GB partition contains a Knoppix DVD KNOPPIX file which permits the boot of the Knoppix 3.4 CeBit remaster ..toram... when the DVD is loaded in the CD/DVD reader. This provides 4GB of swap but only some 900MB of free memory. It loads in kernel 2.6.3 whereas the CD loads kernel 2.6.5. There are 4.9GB of program material provided in the DVD format (Limited by the legacy of inherent isolinux limits).
One experiment conducted with the system as loaded into ram involved transferring a 300MB file from desktop to a directory created called RAM1. The file transferred at 200MB/sec, thus confirming the true install ..toram..of all data.
My system is athlon1900+ having 3GB of 2100DDRAM.
Examining the characteristics of loading additional data into the memory via file transfer from external sources suggests that the new data drives the memory content already present in physical ram into the swap area (slower, due to USB interface in my system).
I invite comment on this apparent characteristic of memory management. Thus the new data appears in physical ram, and if enough is added, swap begins to build (slower).
I have just begun studying what might happen next, with Linux...anything!
Admittedly, using the "C" drive for swap and Knoppix loading would provide higher speed but this arrangement left my system in pristine condition while the experiment was performed.
I expect to try installing the USB HDD as "C" HDD and compare performance.
Similar Threads
-
By aay in forum Tips and Tricks
Replies: 18
Last Post: 11-02-2006, 02:18 AM
-
By mlap in forum Customising & Remastering
Replies: 35
Last Post: 04-18-2005, 09:21 AM
-
By lilsirecho in forum Knoppix DVD
Replies: 0
Last Post: 10-03-2004, 01:45 AM
-
By lilsirecho in forum The Lounge
Replies: 0
Last Post: 09-04-2004, 12:52 AM
-
By AzureD in forum General Support
Replies: 4
Last Post: 03-27-2004, 03:20 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules

WAVLINK RAID 2 Bay Hard Drive Docking Station SATA 2.5/3.5'' SSD HDD Enclosure
$68.39

Broadcom 9600-24i Tri-Mode RAID Controller 4.0 NVMe SAS SATA NEW 05-50111-01003
$639.69

G-Technology G-SPEED Studio XL 48TB Thunderbolt 2 Storage
$200.00

Intel VROC Premium RAID Controller Card PCIe Add-On Module VROCPREMMOD
$265.00

2-Bay/4-Bay Hard Drive Enclosure for 3.5"/2.5'' SATA HDD/SSD 10Gbps USB-C 3.2
$75.99

Lot Mini SAS SFF-8643 To 4 SATA 7pin Hard Disk 6Gbps Data Server Raid Cable 1M
$1150.00

Broadcom LSI 9305-16i 12Gbps SAS-3 PCIe x8 HBA 16-Ports Raid Controller
$64.99

Dell 3KDWX PERC H755 12G 8GB Cache Front RAID Controller
$999.99

EMC VNXe3100 EPE 12-LFF 3.5" NAS Storage Array 12*3TB SAS HDD 2*303-137-000D
$224.99

Broadcom 9600-24i RAID Controller PCIe Gen 4.1 Tri-Mode NEW 05-50111-01004
$649.99