Hi,

I installed knoppix in HD using knx-install. First, I started knoppix from CD using noscsi cheatcode, because the system hanged on boot with message "Probing SCSI... aic7xxx.o". (Before disabling scsi detection, I disabled all the "Power savings" settings, since I read in the forums that it could affect).

Now the system does not find eth0 when I issue a ifconfig.

Here is the lspci -v output:


00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: bus master, medium devsel, latency 0
Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: f0100000-f01fffff
Prefetchable memory behind bridge: f8000000-fbffffff
Capabilities: [80] Power Management version 2

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0

00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 64
I/O ports at 1000 [size=16]
Capabilities: [c0] Power Management version 2

00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at 1020 [size=32]
Capabilities: [80] Power Management version 2

00:07.4 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Flags: medium devsel
Capabilities: [68] Power Management version 2

00:07.6 Communication controller: VIA Technologies, Inc. AC97 Modem Controller (rev 20)
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: medium devsel
I/O ports at 1400 [disabled] [size=256]
Capabilities: [d0] Power Management version 2

00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: medium devsel
I/O ports at 1800 [disabled] [size=256]
Memory at f0000000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [50] Power Management version 2

00:0c.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: bus master, medium devsel, latency 168, IRQ 10
Memory at 18000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 18400000-187ff000 (prefetchable)
Memory window 1: 18800000-18bff000
I/O window 0: 00004400-000044ff
I/O window 1: 00004800-000048ff
16-bit legacy interface ports at 0001

00:0c.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: bus master, medium devsel, latency 168, IRQ 10
Memory at 18001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 18c00000-18fff000 (prefetchable)
Memory window 1: 19000000-193ff000
I/O window 0: 00004c00-00004cff
I/O window 1: 00006000-000060ff
16-bit legacy interface ports at 0001

00:0c.2 FireWire (IEEE 1394): Texas Instruments PCI4451 IEEE-1394 Controller (prog-if 10 [OHCI])
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: medium devsel
Memory at f0000800 (32-bit, non-prefetchable) [disabled] [size=2K]
Memory at f0004000 (32-bit, non-prefetchable) [disabled] [size=16K]
Capabilities: [44] Power Management version 2

00:0d.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12)
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: bus master, medium devsel, latency 64
I/O ports at 1c00 [size=256]
Capabilities: [c0] Power Management version 2

01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev 02) (prog-if 00 [VGA])
Subsystem: CLEVO/KAPOK Computer: Unknown device 8586
Flags: stepping, fast Back2Back, 66Mhz, medium devsel, IRQ 11
Memory at f8000000 (32-bit, prefetchable) [size=64M]
I/O ports at 5000 [size=256]
Memory at f0100000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2


Any hint will be very much appreciated.

TIA