I got the following message when doing a 'cat /proc/cmdline'

================================================== =======================
auto BOOT_IMAGE=Linux ro root=302 ramdisk_size=100000 init=/etc/init lang=us apm=power-off xmodule=fbdev nomce quiet knoppix myconfig=scan
================================================== =======================
And the lilo.conf is like that :

================================================== =======================

# /etc/lilo.conf - See: 'lilo(' and 'lilo.conf(5)',
# --------------- 'install-mbr(', '/usr/share/doc/lilo/',
# and '/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run 'lilo' after you make changes to this |
# | conffile, '/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run 'lilo'. |
# | |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81

#disk=/dev/sda
# bios=0x80

# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. ('/')
#
root=/dev/hda2

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using 'compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact

# Default menu for Debian. (Using the images from debian-bootscreen)
# from Philipp Wolfer <[email protected]>.
bitmap=/usr/share/lilo/debianlilo.bmp
bmp-colors=1,,0,2,,0
bmp-table=120p,173p,1,15,17
bmp-timer=254p,432p,1,0,0

# Install the specified file as the new boot sector.
# LILO supports built in boot sectory, you only need
# to specify the type, choose one from 'text', 'menu' or 'bitmap'.
# new: install=bmp old: install=/boot/boot-bmp.b
# new: install=text old: install=/boot/boot-text.b
# new: install=menu old: install=/boot/boot-menu.b or boot.b
# default: 'menu' is default, unless you have a bitmap= line
# Note: install=bmp must be used to see the bitmap menu.
# install=menu
# install=bmp
install=bmp

# Specifies the number of _tenths_ of a second LILO should
# wait before booting the first image. LILO
# doesn't wait if DELAY is omitted or if DELAY is set to zero.

delay=20

# Prompt to use certaing image. If prompt is specified without timeout,
# boot will not take place unless you hit RETURN
prompt
timeout=50

# Specifies the location of the map file. If MAP is
# omitted, a file /boot/map is used.
map=/boot/map

# Specifies the VGA text mode that should be selected when
# booting. The following values are recognized (case is ignored):
# NORMAL select normal 80x25 text mode.
# EXTENDED select 80x50 text mode. The word EXTENDED can be
# abbreviated to EXT.
# ASK stop and ask for user input (at boot time).
# <number> use the corresponding text mode. A list of available modes
# can be obtained by booting with vga=ask and pressing [Enter].
vga=788

# You can set a password here, and uncomment the 'restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an 'append'
# statement in 'lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like 'Linux init=/bin/sh',
# and thus becoming 'root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use 'install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM 'install-mbr('.
#
# password=tatercounter2000

# You can put a customized boot message up if you like. If you use
# 'prompt', and this computer may need to reboot unattended, you
# must specify a 'timeout', or it will sit there forever waiting
# for a keypress. 'single-key' goes with the 'alias' lines in the
# 'image' configurations below. eg: You can press '1' to boot
# 'Linux', '2' to boot 'LinuxOLD', if you uncomment the 'alias'.
#
# message=/boot/bootmess.txt
# prompt
# single-key
# delay=100
# timeout=100

# Kernel command line options that apply to all installed images go
# here. See: The 'boot-prompt-HOWO' and 'kernel-parameters.txt' in
# the Linux kernel 'Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default="Linux"

image=/boot/vmlinuz
label="Linux"
initrd=/boot/initrd.img
append="ramdisk_size=100000 init=/etc/init lang=us apm=power-off xmodule=fbdev nomce quiet knoppix myconfig=scan"
read-only
image=/boot/vmlinuz-2.4.27
label="Linux(2.4)-1"
initrd=/boot/initrd.img-2.4.27
append="ramdisk_size=100000 init=/etc/init lang=us apm=power-off xmodule=fbdev nomce quiet knoppix myconfig=scan"
read-only

image=/boot/vmlinuz-2.6.9
label="Linux(2.6)-2"
initrd=/boot/initrd.img-2.6.9
append="ramdisk_size=100000 init=/etc/init lang=us apm=power-off xmodule=fbdev nomce quiet knoppix myconfig=scan"
read-only

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the 'other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
# other=/dev/hdc1
# label="WinXP/2K(hdc1)"root@box:/etc#
================================================== ===================

This is the XF86Config-4

================================================== ===================
# Auto-generated by KNOPPIX mkxf86config

Section "ServerLayout"

# PS/2 Mouse not detected
# Serial Mouse not detected
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "USB Mouse" "CorePointer"
EndSection

Section "Files"

# Additional fonts: Locale, Gimp, TTF...
# FontPath "/usr/X11R6/lib/X11/fonts/latin2/75dpi"
# FontPath "/usr/X11R6/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
FontPath "/usr/X11R6/lib/X11/fonts/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/misc"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo"
FontPath "/usr/X11R6/lib/X11/fonts/PEX"
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic"
FontPath "/usr/X11R6/lib/X11/fonts/Type1"
FontPath "/usr/share/fonts/ttf/western"
FontPath "/usr/share/fonts/ttf/decoratives"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/latex-ttf-fonts"
FontPath "/usr/X11R6/lib/X11/fonts/defoma/CID"
FontPath "/usr/X11R6/lib/X11/fonts/defoma/TrueType"
EndSection

Section "Module"
Load "ddc" # ddc probing of monitor
Load "GLcore"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "speedo"
Load "type1"
Load "freetype"
Load "record"
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection

Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

Section "Monitor"
# DDC-probed
# DDC-probed
# These are the DDC-probed settings reported by your monitor.
# 1024x768, 75.0Hz; hfreq=61, vfreq=76
Identifier "Monitor0"
VendorName "PHL"
ModelName "PHL0804"
HorizSync 31.5 - 48.5
VertRefresh 56.0 - 76.0

ModeLine "1024x768" 60.0 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
# ModeLine "800x600" 49.5 800 816 896 1056 600 601 604 625 +hsync +vsync
# ModeLine "800x600" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
# ModeLine "640x480" 31.5 640 656 720 840 480 481 484 500 -hsync -vsync
# ModeLine "640x480" 31.5 640 656 696 816 480 481 484 504 -hsync -vsync
# ModeLine "640x480" 25.2 640 648 744 784 480 482 484 509 -hsync -vsync
# ModeLine "640x480" 43.2 640 680 744 848 480 481 484 509 -hsync +vsync
# ModeLine "768x576" 35.0 768 792 872 976 576 577 580 597 -hsync +vsync
# ModeLine "768x576" 42.9 768 800 880 992 576 577 580 601 -hsync +vsync
# ModeLine "768x576" 45.5 768 808 888 1008 576 577 580 602 -hsync +vsync
# ModeLine "768x576" 51.8 768 808 888 1008 576 577 580 605 -hsync +vsync
# ModeLine "768x576" 62.6 768 816 896 1024 576 577 580 611 -hsync +vsync
# ModeLine "800x600" 68.2 800 848 936 1072 600 601 604 636 -hsync +vsync
# ModeLine "1024x768" 113.3 1024 1096 1208 1392 768 769 772 814 -hsync +vsync
# ModeLine "1152x864" 81.6 1152 1216 1336 1520 864 865 868 895 -hsync +vsync
# ModeLine "1152x864" 119.7 1152 1224 1352 1552 864 865 868 907 -hsync +vsync
# ModeLine "1152x864" 143.5 1152 1232 1360 1568 864 865 868 915 -hsync +vsync
# ModeLine "1280x960" 124.5 1280 1368 1504 1728 960 961 964 1001 -hsync +vsync
# ModeLine "1280x960" 129.9 1280 1368 1504 1728 960 961 964 1002 -hsync +vsync
# ModeLine "1280x960" 179.0 1280 1376 1520 1760 960 961 964 1017 -hsync +vsync
# ModeLine "1280x1024" 191.0 1280 1376 1520 1760 1024 1025 1028 1085 -hsync +vsync
# ModeLine "1400x1050" 122.6 1400 1488 1640 1880 1050 1051 1054 1087 -hsync +vsync
# ModeLine "1400x1050" 149.3 1400 1496 1648 1896 1050 1051 1054 1094 -hsync +vsync
# ModeLine "1400x1050" 155.8 1400 1496 1648 1896 1050 1051 1054 1096 -hsync +vsync
# ModeLine "1400x1050" 179.3 1400 1504 1656 1912 1050 1051 1054 1103 -hsync +vsync
# ModeLine "1400x1050" 214.4 1400 1512 1664 1928 1050 1051 1054 1112 -hsync +vsync
# ModeLine "1600x1200" 280.6 1600 1728 1904 2208 1200 1201 1204 1271 -hsync +vsync
Option "DPMS" "true"
EndSection

Section "Device"

### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
#Option "sw_cursor"
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
# The following line is auto-generated by KNOPPIX mkxf86config
# BusID "PCI:1:0:0"
Identifier "Card0"
Driver "fbdev"
VendorName "All"
BoardName "All"
EndSection

Section "Screen"

# DefaultColorDepth 16
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Depth 1
Modes "1024x768" # "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768" # "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" # "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768" # "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" # "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" # "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" # "800x600" "640x480"
EndSubSection
EndSection

Section "DRI"
Mode 0666
EndSection
================================================== ========================