Detection of internal wifi fails

[r00tNinj4]

i am using a winbook v220 for this, the specs are as follows:


WinBook V220 Notebook

Operating System Microsoft Windows XP Home Edition

Processor Intel® Pentium® 4 Processor

Processor Speed 2.8GHz

Level 1 Cache 8KB Level 1 Cache + 12,000 uOps Trace Cache

Level 2 Cache 512KB Level 2 Cache

Data Bus Speed 400MHz Frontside Bus

RAM Installed 512MB PC-2700 DDR RAM (Expandable to 512MB)

Memory Configuration (1) 512MB SO-DIMM Memory Module

Memory Slots Available 0 available 200-pin SO-DIMM Slots

Hard Drive 60GB UltraDMA ATA/100 Hard Drive

Multimedia Drive Combo 8x DVD-ROM / 24x10x24 CD-RW Drive

Display Type 15.0" XGA Active Matrix Display

Video Card Integrated 4x AGP SiS M661FX Video Chipset

Video Memory Installed Up to 64MB of Shared Memory

Internal Max Resolution 1024 x 768 at 24-bit (16.7M colors)

Sound Card Integrated SoundBlaster Pro Compatible Audio Chipset

Sound Output Mode 16-bit Stereo

Audio Input Integrated Mono Microphone

Modem Integrated 56K V.90 Fax/Modem Adapter

Data transfer rate 56Kbps Data / 14.4Kbps Fax

Network Features Integrated 10/100 Fast Ethernet Adapter

Wireless Network Feature Integrated IEEE-802.11b/g 54Mbps Wireless Network Adapter

Ports and Connectors (1) Parallel 25-pin Port; (1) VGA 15-pin Port; (1) TV Out S-Video Port; (2) USB 2.0 Type "A" Ports; (1) FireWire 4- Port; (1) Modem RJ-11 Port; (1) Network RJ-45 Port; (1) Microphone Port; (1) Audio Line Out Port

Expansion Slots 1 (1 free) Cardbus PCMCIA type I or II Slot

Input Devices Keyboard, Touchpad

Power Supply Universal AC adapter



now the way i understand it, this uses the intel pro chipset 2200

i can modprobe ipw2200 and its loads well, no errors. but iwconfig tells me theres no wireless adaptters found.

--DMESG--

Linux version 2.6.11.9 (root@Knoppix) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 SMP Mon M
ay 16 03:17:22 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfd0000 (usable)
BIOS-e820: 000000001dfd0000 - 000000001dfdf000 (ACPI data)
BIOS-e820: 000000001dfdf000 - 000000001e000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 122832
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 118736 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f7980
ACPI: RSDT (v001 A M I OEMRSDT 0x09000401 MSFT 0x00000097) @ 0x1dfd0000
ACPI: FADT (v002 A M I OEMFACP 0x09000401 MSFT 0x00000097) @ 0x1dfd0200
ACPI: MADT (v001 A M I OEMAPIC 0x09000401 MSFT 0x00000097) @ 0x1dfd0390
ACPI: OEMB (v001 A M I AMI_OEM 0x09000401 MSFT 0x00000097) @ 0x1dfdf040
ACPI: DSDT (v001 G733E G733E555 0x00000555 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 1e000000 (gap: 1e000000:e1f80000)
Built 1 zonelists
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off vga=791 init
rd=minirt.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux
__iounmap: bad address c00fffd9
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2520.179 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 480832k/491328k available (1846k kernel code, 9760k reserved, 943k data, 292k init
, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4980.73 BogoMIPS (lpj=249036
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 0
0000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00
000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1462.89 usecs.
task migration cache decay timeout: 2 msecs.
Total of 1 processors activated (4980.73 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1099k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS963 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 16)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
pnp: 00:08: ioport range 0x200-0x20f has been reserved
audit: initializing netlink socket (disabled)
audit(1117304084.818:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xd0000000, mapped to 0xde880000, using 3072k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at cbc0:0004
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdcMA, hddMA
Probing IDE interface ide0...
hda: FUJITSU MHT2060AT, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Slimtype COMBO LSC-24082K, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1 hda2
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.10 loaded.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1
Firmware: 5.9
180 degree mounted touchpad
Sensor: 53
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio2
psmouse.c: TouchPad at isa0060/serio2/input0 lost sync at byte 1
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI wakeup devices:
EUSB USB USB2 USB3 MAC S139 AC97 MC97 CBUS
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
pas16: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 386
gcc-3.3'
psi240i: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 38
6 gcc-3.3'
seagate: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 38
6 gcc-3.3'
t128: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 386 g
cc-3.3'
u14_34f: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 38
6 gcc-3.3'
wd7000: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 386
gcc-3.3'
usbcore: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 38
6 gcc-3.3'
ehci_hcd: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 3
86 gcc-3.3'
uhci_hcd: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 3
86 gcc-3.3'
ohci_hcd: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 3
86 gcc-3.3'
ieee1394: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 3
86 gcc-3.3'
ohci1394: version magic '2.6.11 SMP preempt 386 gcc-3.3' should be '2.6.11.9 SMP preempt 3
86 gcc-3.3'
Unable to identify CD-ROM format.
VFS: Can't find an ext2 filesystem on dev hda.
FAT: invalid media value (0xea)
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.01
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 30827 blocks, 65536 bytes/block, largest block is 65562 byt
es.
ISO 9660 Extensions: RRIP_1991A
Registering unionfs version $Id: main.c,v 1.85 2005/03/14 22:19:49 dquigley Exp $
Freeing unused kernel memory: 292k freed
Generic RTC Driver v1.07
ACPI: AC Adapter [ADP0] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Processor [CPU1] (supports 8 throttling states)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:00:0a.0 [1019:b733]
Yenta: adjusting diagnostic: 40 -> 60
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x000c1002, devctl 0x44
Yenta: ISA IRQ mask 0x0000, PCI irq 16
Socket status: 30000006
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: excluding 0x828-0x877 0x880-0x887 0x898-0x89f
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 20, pci mem 0xdfffb000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
ohci_hcd 0000:00:03.1: irq 21, pci mem 0xdfffc000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
ohci_hcd 0000:00:03.2: irq 22, pci mem 0xdfffd000
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 3-1: new full speed USB device using ohci_hcd and address 2
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <[email protected]>
ACPI: PCI interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[dfffa000-dfffa7ff] Max Packet048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000ae6ff2809d8]
eth1394: $Rev: 1224 $ Ben Collins <[email protected]>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
sis900.c: v1.08.07 11/02/2003
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth1: SiS 900 PCI Fast Ethernet at 0xe800, IRQ 19, 00:11:5b:80:58:02.
Intel 810 + AC97 Audio, version 1.01, 03:46:36 May 16 2005
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18
i810: SiS 7012 found at IO 0xec00 and 0xe400, MEM 0x0000 and 0x0000, IRQ 18
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALG64 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
i810_audio: setting clocking to 48566
Linux agpgart interface v0.100 (c) Dave Jones
NET: Registered protocol family 17
eth1: Media Link On 100mbps full-duplex
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
eth1: Media Link On 100mbps full-duplex
psmouse.c: TouchPad at isa0060/serio2/input0 - driver resynched.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03702e0(lo)
IPv6 over IPv4 tunneling driver
eth1: no IPv6 routers present
eth1: Media Link Off
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timeout, status 00000004 00000000
eth1: Media Link On 100mbps full-duplex
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.4
ipw2200: Copyright(c) 2003-2004 Intel Corporation


--lsmod--


Module Size Used by
ipw2200 162440 0
firmware_class 11264 1 ipw2200
ieee80211 44804 1 ipw2200
ieee80211_crypt 8648 2 ipw2200,ieee80211
md5 7680 1
ipv6 234912 6
snd_mixer_oss 18688 0
snd 46308 1 snd_mixer_oss
autofs4 18820 1
af_packet 20104 0
agpgart 30512 0
i810_audio 36884 0
ac97_codec 20108 1 i810_audio
soundcore 11104 2 snd,i810_audio
sis900 20612 0
i2c_sis96x 8580 0
i2c_core 21248 1 i2c_sis96x
parport_pc 38596 0
parport 33480 1 parport_pc
8250 41692 0
serial_core 21120 1 8250
eth1394 21768 0
ohci1394 33028 0
ieee1394 300600 2 eth1394,ohci1394
usbhid 42176 0
ohci_hcd 21896 0
uhci_hcd 31376 0
usbcore 101496 4 usbhid,ohci_hcd,uhci_hcd
pcmcia 21776 2
yenta_socket 21896 1
rsrc_nonstatic 12160 1 yenta_socket
pcmcia_core 42272 3 pcmcia,yenta_socket,rsrc_nonstatic
video 18308 0
thermal 14984 0
processor 24552 1 thermal
fan 7300 0
container 7296 0
button 9104 0
battery 12420 0
ac 7556 0
genrtc 12060 0
unionfs 829844 1
cloop 16800 1


--iwconfig--


lo no wireless extensions.

eth0 no wireless extensions.

eth1 no wireless extensions.

sit0 no wireless extensions.


how can i get linux to detect my internal card??
thanks in advance

[thedead]

i have this EXACT same problem. Different laptop though.

[r00tNinj4]

bump

[knopx4me]

If your wifi card is ipw2200, then do the following:
create the following file /etc/init.d/ipw2200:
__________ Strat below this line ___________
#!/bin/sh
#
modprobe -r ipw2200
modprobe ipw2200
ifup -a
________ Stop above this line ______________
save it and execute the following command with root preveilage:
chmod +x /etc/init.d/ipw2200
then run rcconf and select ipw2200 and hit ok.

To test it, just run /etc/init.d/ipw2200 and should work. if it does not, just setup the essid from KNOPPIX menu. If it works fine, it will detect it every time you reboot your system.