Setting up a WPC54G ver2 on knoppix 4.0 --Help

[jOVENASO]

I have an WPC54G ver2
so i download some drivers to istalled apperantly work becuze i see the power on of the wireless card but it seems not to get my network connect all is see is some off/any which mean that is not connected some help pls maybe im missing something thank you after i done ill post my result with a good tutorial on how to make your wirelles done thnaks again

So I stared my configuration with

root@0[wireless]# ndiswrapper -i lstinds.inf
Installing lstinds
root@0[wireless]# ndiswrapper -l
Installed ndis drivers:
lstinds driver present, hardware present
root@0[wireless]# modprobe ndiswrapper

root@0[wireless]# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11g ESSIDff/any
Mode:Managed Frequency:2.412 GHz Access Point: 00:00:00:00:00:00
Bit Rate:54 Mb/s Tx-Power:10 dBm Sensitivity=0/3
RTS thr:4096 B Fragment thr:4096 B
Encryption keyff
Power Managementff
Link Quality:100 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0



root@0[wireless]# dmesg
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
ACPI-0352: *** Error: Looking up [Z007] in namespace, AE_NOT_FOUND
search_node cbec4320 start_node cbec4320 return_node 00000000
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT1._BST] (Node cbec4220), AE_NOT_FOUND
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
ACPI-0352: *** Error: Looking up [Z007] in namespace, AE_NOT_FOUND
search_node cbec4320 start_node cbec4320 return_node 00000000
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT1._BST] (Node cbec4220), AE_NOT_FOUND
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
ACPI-0352: *** Error: Looking up [Z007] in namespace, AE_NOT_FOUND
search_node cbec4320 start_node cbec4320 return_node 00000000
ACPI-1138: *** Error: Method execution failed [\_SB_.BAT1._BST] (Node cbec4220), AE_NOT_FOUND
APIC error on CPU0: 40(40)

root@0[wireless]# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11g ESSIDff/any
Mode:Managed Frequency:2.412 GHz Access Point: 00:00:00:00:00:00
Bit Rate:54 Mb/s Tx-Power:10 dBm Sensitivity=0/3
RTS thr:4096 B Fragment thr:4096 B
Encryption keyff
Power Managementff
Link Quality:100 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0


root@0[wireless]# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:600 (600.0 b) TX bytes:600 (600.0 b)

root@0[wireless]# iwconfig wlan0 essid myessid key sassword; pump -i wlan0
Error for wireless request "Set Encode" (8B2A) :
SET failed on device wlan0 ; Invalid argument.

[Blackbomb]

Did you get drivers from Linksys?.... I had trouble using any Linksys drivers... I have a WPC54G ver. 1.2 card w/ a Broadcom 4306 chip... is you card the same? if it is check my other post it may help....

the HP driver is an older driver but it's the only one I found that I could get to work w/ either my internal wifi or my WPC54G card..

http://www.knoppix.net/forum/viewtopic.php?t=21764


Hope it helps....

If you have trouble finding the driver let me know...

Blackbomb