apache2 not working no index.html

[babelbrennt]

Spoke too soon. I thought my disk was working and didn't try index page with apache2 as my php5 and tomcat5 default pages came up I assumed index.html would. I have changed apache2.conf, /etc/default/apache2 to 0 and commented out redirect in /etc/apache2/sites-available/default. Suggestions found on the web. I've put the contents of these below to see if anything appears to be wrong
</Directory>
<Directory /var/www/>
Options Indexes FollowSymLinks MultiViews
AllowOverride None
Order allow,deny
allow from all
# This directive allows us to have apache2's default start page
# in /apache2-default/, but still have / go to the right place
#RedirectMatch ^/$ /apache2-default/
</Directory>

ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/
<Directory "/usr/lib/cgi-bin">
AllowOverride None
Options ExecCGI -MultiViews +SymLinksIfOwnerMatch
Order allow,deny
Allow from all
</Directory>

ErrorLog /var/log/apache2/error.log

# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn

CustomLog /var/log/apache2/access.log combined
ServerSignature On

Alias /doc/ "/usr/share/doc/"
<Directory "/usr/share/doc/">
Options Indexes MultiViews FollowSymLinks
AllowOverride None
Order deny,allow
Deny from all
Allow from 127.0.0.0/255.0.0.0 ::1/128
</Directory>

</VirtualHost>

[babelbrennt]

When this didn't work I added the server name like this:


# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
#
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses (0.0.0.0)
#
#Listen 12.34.56.78:80
Listen 80

#ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
#
ServerAdmin webmaster@localhost

I got the following error report:

/etc/init.d/apache2 force-reload
Forcing reload of web server: Apache2 ... no pidfile found! not running?apache2: Could not determine the server's fully qualified domain name, using 127.0.0.1 for ServerName
(9Address already in use: make_sock: could not bind to address [::]:80
no listening sockets available, shutting down
Unable to open logs

does anyone know what the problem is

[babelbrennt]

and the following from my /etc/hosts file

127.0.0.1 Knoppix localhost

# The following lines are desirable for IPv6 capable hosts
# (added automatically by netbase upgrade)

::1 ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts

[eddt]

I am experiencing the same problem and have tried virtually exactly the same steps.

further problems I have discovered is that a site created in a subfolder is accessible but all image links and css include statements are dead.

have you got any closer to a solution or can anyone suggest one.

[babelbrennt]

sorry when i finished my project i didn't look at it again. in the end i just carried on with an updated version of apache 1.3. I haven't looked at knoppix for a while so i don't know what version is current, but the KNOPPIX 4.0 version had knoppix 2.0 preinstalled I think. Good Luck and if you do get an answer please post it for future reference

[sittisaks]

I found out that when I create a simple html file which just contain somthing like
<html>
<body>
blar blar blar.....
</body>
</html>

and if the file size is less than or equal 255 bytes. The page will display correctly. If the file size is greather than 255 then it will have the problem. Don't see the problem when using within the chroot. May be the problem is from UNIONFS+Apache2???

[valonso]

I solved it by adding this line to httpd.conf:

EnableSendfile Off

Found here:
http://www.apachefriends.org/f/viewt...?p=86298#86298
(in german)

Best regards

[alitosdavila]

knoppix 5.0.1
apache2

you need to add

EnableSendfile Off

to httpd.conf