-

Originally Posted by
SiKing
Did you configure it first? K Menu -> KNOPPIX -> Network/Internet -> ADSL/PPPOE configuration
Uh...It seems that you misunderstood me. I mean the configuration is correct, and the connection is established, but any of the programs didn't use the ppp0 connection.
Maybe you should see this:
Code:
eth0 Link encap:Ethernet HWaddr 00:10:DC:9C:53:66
inet addr:192.168.1.25 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::210:dcff:fe9c:5366/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5134 errors:0 dropped:0 overruns:0 frame:0
TX packets:318 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:365258 (356.6 KiB) TX bytes:21794 (21.2 KiB) // <--pay attention to this
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:100 (100.0 b) TX bytes:100 (100.0 b)
ppp0 Link encap:Point-to-Point Protocol
inet addr:172.16.47.242 P-t-P:10.10.10.10 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1480 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:54 (54.0 b) TX bytes:54 (54.0 b) // <--pay attention to this
A few seconds later .
eth0 Link encap:Ethernet HWaddr 00:10:DC:9C:53:66
inet addr:192.168.1.25 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::210:dcff:fe9c:5366/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6522 errors:0 dropped:0 overruns:0 frame:0
TX packets:353 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:467130 (456.1 KiB) TX bytes:22904 (22.3 KiB) // <--pay attention to this
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:100 (100.0 b) TX bytes:100 (100.0 b)
ppp0 Link encap:Point-to-Point Protocol
inet addr:172.16.47.242 P-t-P:10.10.10.10 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1480 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:54 (54.0 b) TX bytes:54 (54.0 b) // <--pay attention to this
Similar Threads
-
By Gusse in forum Networking
Replies: 1
Last Post: 01-31-2010, 04:10 PM
-
By kuddo in forum Networking
Replies: 1
Last Post: 10-03-2006, 07:52 AM
-
By loksipan in forum Networking
Replies: 0
Last Post: 03-05-2006, 08:24 AM
-
By b0 in forum Networking
Replies: 11
Last Post: 09-25-2005, 03:49 PM
-
By funky in forum Networking
Replies: 0
Last Post: 02-08-2004, 11:26 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules

MegaRAID 9580-8i8e 16-port 12G SAS/SATA/NVMe 8GB PCIe RAID - 05-50076-00
$1619.19

Intel VROC Premium RAID Controller Card PCIe Add-On Module VROCPREMMOD
$265.00

Areca ARC-1882IX-24 (16i4e)24-Port RAID Controller Card w/BBU /HDD Monitor Board
$300.00

OWC Mercury Elite Pro 2 Bay RAID Enclosure with USB 3.2 for Dual 3.5 inch HDDs
$87.99

Broadcom LSI 9305-16i 12Gbps SAS-3 PCIe x8 HBA 16-Ports Raid Controller
$64.99

Dell PowerEdge HBA330 LP PCI-E 12GBs RAID SAS Controller Adapter J7TNV
$18.95

LSI 9305-16i SATA SAS 12Gbs Controller card PCIe 3.0 IT-Mode w/SAS SATA cable US
$125.98

NVME M.2 Adapter Card PCIE X16 Splitter Expansion Controller 4-Disk Soft RAID
$24.43

Broadcom 9600-24i RAID Controller PCIe Gen 4.1 Tri-Mode NEW 05-50111-01004
$649.99

Broadcom MegaRAID 9480-8e Fujitsu PRAID EP540e SAS RAID Card (Replac 9380-8e) 8i
$228.00