How do I make my Seagate 2Tb usb hdd work in Knoppix?

[winger9]

Summary:

I've just bought a Seagate 2Tb "expansion portable drive", model STEA2000400,
with USB 3 connection, formatted as ntfs. The documentation says "System
requirements: Windows 7 or 8" but I assume it should work with Linux/Knoppix (I really
like the neat design of the drive).

My system is Live Knoppix 7.0.2 installed on hard drive, with kernel 3.3.7.

So far, the Seagate drive has only worked once, when I first plugged it in* (usb
3 slot). (*After boot). It automounted, and its files were displayed in the
pcmanfm file manager. By automount, I mean when the small window appears and
says something like "Do you want to open this device in file manager".

But since then, each time I plug it in, it doesn't work (it works OK in Windows
7). When I plug it in, sometimes it gets mounted by the system (even if the
automount dialogue doesn't appear), and sometimes it doesn't get mounted.

When it's not mounted, the dmesg command says

[ 9134.211695] sd 8:0:0:0: sense urb submission failure

and the message repeats continuously (with different "[...]" nos.) and repeats
across subsequent dmesgs and across logging out and in.

When I plug the drive in BEFORE booting, the system mounts the drive, and dmesg
gives the following message continuously (it gave the same continuous message
when I repeated the dmesg command):

[ 105.827668] sd 8:0:0:0: rejecting I/O to offline device

My humble questions are:

Could you tell me why the drive isn't working in Knoppix, and what I need to do
to get it working? I really like the neat design of the drive and would very
much like to keep it and get it working.

Should I look for another usb hdd that specifically says it works with Linux?


Full Details:

When the drive worked that first time, and its files were displayed in pcmanfm,
the mount command showed

/dev/sdb1 on /media/sdb1 type fuseblk (rw,nosuid,nodev,relatime,user_id=
1000,group_id=0,allow_other,blksize=4096)

AND dmesg showed

[ 3104.772532] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 3104.789326] usb 4-2: New USB device found, idVendor=0bc2, idProduct=231a
[ 3104.789336] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3104.789342] usb 4-2: Product: Expansion
[ 3104.789347] usb 4-2: Manufacturer: Seagate
[ 3104.789351] usb 4-2: SerialNumber: NA8PEPNV
[ 3104.791381] scsi8 : uas
[ 3104.793020] scsi 8:0:0:0: Direct-Access     Seagate  Expansion        0708
PQ: 0 ANSI: 6
[ 3104.793363] sd 8:0:0:0: Attached scsi generic sg2 type 0

Also when the drive worked that first time, and its files were displayed
in pcmnfm; about 15 minutes later, when I reselected the drive in pcmanfm, no
files were displayed, and pcmanfm said

"The specified directory is not valid".

I then opened the nautilus file manager, and when I selected the drive, nautilus
said

"Could not display /media/sdb1. Error: Error when getting information for file
/media/sdb1: Input/output error. Please select another viewer and try again."

On the occasion when I plugged the drive in BEFORE booting, and the system
mounted it, I can't remember if the automount dialogue appeared or not.

[knp]

Hi winger9

Perhapstoo late for you ?

Suggestions of a very newbie:

1- Verify your "bios" to authorize "automatic hdd

recognition"

2- Perhaps your "2To_HDD" is too big (depending

on the version of the processor)

3- In that case you may split he HDD in 2 (or more)

partitions.

4- In my case it was (and is yet!) a "processor problem"

for a "1To_HDD" (but ONLY FOR BOOTING the PC!

Hope for you !

knp