toshiba satellite 1800 654 dont detect hd

[koszopal]

hi
Knoppix latest version (26.07-ENG) cant detect and hangs on
when detecting hd while boot knoppix (testcd is ok) , failsafe (he wrote hda lost interrupt when he tryed) Help me ((
koszopal
PS here is log from lspci -v and dmesg
...........................................
00:00.0 Host bridge: ALi Corporation M1644/M1644T Northbridge+Trident (rev 01)
Flags: bus master, medium devsel, latency 0
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <available only to root>

00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (prog-if 00 [Normal decode])
Flags: bus master, slow devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f7f00000-fdffffff

00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0004
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>

00:04.0 IDE interface: ALi Corporation M5229 IDE (rev c3) (prog-if f0)
Subsystem: Toshiba America Info Systems: Unknown device 0004
Flags: bus master, medium devsel, latency 64
I/O ports at eff0 [size=16]
Capabilities: <available only to root>

00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at 1000 [size=256]
Memory at 18000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>

00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: Toshiba America Info Systems: Unknown device 0004
Flags: bus master, medium devsel, latency 0
Capabilities: <available only to root>

00:08.0 Bridge: ALi Corporation M7101 PMU
Subsystem: Toshiba America Info Systems: Unknown device 0001
Flags: medium devsel

00:0a.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d)
Subsystem: Toshiba America Info Systems 8255x-based Ethernet Adapter (10/100)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f7efe000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ef40 [size=64]
Memory at f7ec0000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <available only to root>

00:11.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to Cardbus Bridge with ZV Support (rev 32)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Flags: bus master, slow devsel, latency 168, IRQ 11
Memory at 18001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory window 0: 18400000-187ff000 (prefetchable)
Memory window 1: 18800000-18bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001

00:11.1 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to Cardbus Bridge with ZV Support (rev 32)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Flags: bus master, slow devsel, latency 168, IRQ 11
Memory at 18002000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory window 0: 18c00000-18fff000 (prefetchable)
Memory window 1: 19000000-193ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
16-bit legacy interface ports at 0001

01:00.0 VGA compatible controller: Trident Microsystems CyberBlade XPAi1 (rev 82) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Flags: bus master, 66Mhz, medium devsel, latency 8, IRQ 11
Memory at fc000000 (32-bit, non-prefetchable) [size=32M]
Memory at fbc00000 (32-bit, non-prefetchable) [size=4M]
Memory at f8000000 (32-bit, non-prefetchable) [size=32M]
Memory at f7ff8000 (32-bit, non-prefetchable) [size=32K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: <available only to root>
----------------------------------
here dmesg
-------------------------------------
Linux version 2.4.21-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Fre Jul 25 00:06:47 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000016ff0000 (usable)
BIOS-e820: 0000000016ff0000 - 0000000017000000 (ACPI data)
BIOS-e820: 0000000017000000 - 0000000018000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
367MB LOWMEM available.
On node 0 totalpages: 94192
zone(0): 4096 pages.
zone(1): 90096 pages.
zone(2): 0 pages.
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz testcd
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1095.678 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2175.79 BogoMIPS
Memory: 369444k/376768k available (1258k kernel code, 6936k reserved, 531k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Celeron (Coppermine) stepping 0a
per-CPU timeslice cutoff: 365.59 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1095.2918 MHz.
..... host bus clock speed is 99.5718 MHz.
cpu: 0, clocks: 995718, slice: 497859
CPU0<T0:995712,T1:497840,D:13,S:497859,C:995718>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfe34a, last bus=5
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router ALI [10b9/1533] at 00:07.0
PCI: Found IRQ 11 for device 00:06.0
PCI: Found IRQ 11 for device 00:11.0
PCI: Found IRQ 11 for device 00:11.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xfc000000, mapped to 0xd780d000, size 12288k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:77f8
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:04.0
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xeff0-0xeff7, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0xeff8-0xefff, BIOS settings: hdcMA, hddio
hda: TOSHIBA MK2018GAP, ATA DISK drive
hdc: DV-28E-B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39070080 sectors (20004 MB), CHS=2432/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
hdc: attached ide-scsi driver.
Partition check:
hda: unknown partition table
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01-ww1
No raid array found
No raid array found
No raid array found
Guestimating sector 39069055 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TEAC Model: DV-28E-B Rev: 7.2A
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 3276
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 467k freed
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18f (Release Date: Tue Dec 10 09:54:39 EST 2002)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v1.00
cloop: /cdrom/KNOPPIX/KNOPPIX: 29299 blocks, 65536 bytes/block, largest block is 65562 bytes.
cloop: loaded (max 8 devices)
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
spurious 8259A interrupt: IRQ7.
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:11.0
PCI: Found IRQ 11 for device 00:11.1
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000007
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x3f8-0x3ff 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 00:20:27 Jul 25 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Found IRQ 11 for device 00:02.0
usb-ohci.c: USB OHCI at membase 0xd84b1000, IRQ 11
usb-ohci.c: usb-00:02.0, ALi Corporation. [ALi] USB 1.1 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usbdevfs: remount parameter error
Serial driver version 5.05c (2001-07-0 with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 (0x77 [PCSPP,TRISTATE]
parport0: irq 7 detected
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
PCI: Found IRQ 11 for device 00:0a.0
eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:39:AC:C3:3E, IRQ 11.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xb874c1d3).
Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version 0.14.10h, 00:19:37 Jul 25 2003
PCI: Enabling device 00:06.0 (0000 -> 0003)
PCI: Found IRQ 11 for device 00:06.0
trident: ALi Audio Accelerator found at IO 0x1000, IRQ 11
ac97_codec: AC97 codec, id: (Unknown)
PCI: Found IRQ 11 for device 00:06.0
gameport0: ALi Corporation. [ALi] M5451 PCI AC-Link Controller Audio Device at pci00:06.0 speed 621 kHz
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 306M
agpgart: Detected Ali M1644 chipset
agpgart: AGP aperture is 64M @ 0xf0000000
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
------------------------------------------------

[sturmmoewe]

Hi

I have the same problem. And it seems, you also have a Toshiba Notebook.
I guess it is the new kernel 2.4.21 which causes this error. If I start knoppix using "knoppix noswap" I don't get the lost-IRQ-messages. But then I see that the system doesn't recognise my hd-partitions. /proc/partitions only contain the full disk (hda) with no partitions shown. Giving a 'fdisk -l' shows all my partitions.
Sorry, but I haven't found a solution either. I downgraded back to the latest Knoppix with kernel 2.4.20 which is dated 2003-06-06.

But if you have a solution, please give me a hint. I will do also.

Bye
sturmmoewe

[planglois]

When booting (i use Morphix, a derivative of Knoppix and it's the same problem), boot zith the following option:

morphix dma

or then for knopix, i think:

knoppix dma

It fixed this problem for me.

Now I have another one, my libnsl.1.so got somehow corrupted and i can't login into my system (on my hd), and when booting knoppix/morphix, it says :
hda: unknown partition table.

Now it's my turn, please help! but