-
kernel panic whilst creating dirs and symlinks on ramdisk
Im using Knoppix 3.1 2002-12-10. I have an ide hard drive and an ide cd-rom.
The boot process seem fine until it gets to "Creating directories and symlinks on ramdisk...". It pauses for a while then I get these errors
scsi: aborting command due to timeout: pid 74, scsi0, channel 0, id 0, lun 0 Read (10) 00 00 05 4d 68 00 00 08 00
hdd: timeout waiting for DMA
hdd: ide_dma_timeout: Lets do it again!stat = 0xd0, dma_stat = 0x60
hdd: DMA disabled
Unable to handle kernel NULL pointer dereference at virtual address 00000018
At which point the kernel panics and it doesnt progress any further.
The cd-rom is /dev/hdd, but Knoppix says its "Accessing KNOPPIX CDROM at /dev/scd0...". So I was wondering if it was the ide-scsi emulation that was causing this problem. I have no scsi devices in my machine so I tried the boot command
knoppix noscsi nodma
but the same thing happens. I have had SuSE installed on the same machine for a long time so Im sure the setup can be supported.
Any pointers in the right direction would be very helpful
-
Senior Member
registered user
most likely a cdrom read error, so check the cd itself, and the drive. I'm pretty sure there is no way to turn off scsi emulation, but i don't think it will make a difference.
-
Ah yes, I swapped the cd drive with another one and now it works perfectly. Its a bit ironic that the original drive was the one I used to burn the cd in the first place, ah well its old and i guess its on its way out
Thanks a lot for the help
Similar Threads
-
By gitarzysta in forum Hdd Install / Debian / Apt
Replies: 1
Last Post: 06-03-2004, 08:36 PM
-
By ckassab in forum General Support
Replies: 0
Last Post: 02-04-2004, 11:28 PM
-
By coladicooka in forum Customising & Remastering
Replies: 5
Last Post: 10-23-2003, 02:10 AM
-
By tji in forum Customising & Remastering
Replies: 4
Last Post: 06-12-2003, 06:40 PM
-
By tukun in forum General Support
Replies: 1
Last Post: 05-28-2003, 08:03 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules

Dell PowerEdge VRTX 2.5"x25 Bay Blade Enclosure 4x1600W + 4X M640 (4X Blades)
$1599.99

Dell PowerEdge M630 Blade Server 2x Xeon E5-2680 v4, 2F3MP , 4GDP5 ,R10KJ ,JVFVR
$95.20

Dell PowerEdge M640 Blade Barebone Server Dell P/N: HHB006 Tested Working
$149.99

Cisco UCS 5108 Blade Server Chassis Enclosure N20-C6508 4x PSU 8x Fans 2x Fabric
$174.99

NETAPP HCI NAF-1701 SuperMicro Server 4X BLADE H410C 8X GOLD 5120 4 NODE SERVER
$1499.97

Dell M620 Blade Server Intel Xeon 2x E5-2665 @2.40GHz No HDD and No Ram QTY
$99.95

Datto S4P10 1U Blade Rack Server Intel Xeon D-2143IT 2.20GHz 48GB DDR4 4-Bay PSU
$197.76

Dell Poweredge C6400 24x 2.5’’ 2x 2400W 4x C6420 Nodes H330 | 2x SFP | 8x Trays
$799.99

Dell PowerEdge M620 Blade Server 2x Xeon E5-2680v2 256GB DDR3 RAM NO HDD
$349.99

Dell Poweredge VRTX 25Bay 2.5" 2x PERC 8, 2xCMC, I/O 1GB Pass Through, 4x PS
$578.08