SondCard problem!

[Syslog]

Hi again,

I'm having a problem with my soundcard and i hope somebody could help me!

Here's the deal: knoppix detects the soundcard and the drivers but i only hear is a anowing sound like a beep. I already went to sndconfig and detects well but after apeears an error -> An error ocurred while writing the config file .

I leave here the lspci output:

00:08.0 Multimedia audio controller: ESS Technology ES1969 Solo-1 Audiodrive (rev 02)
Subsystem: ESS Technology: Unknown device 8898
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at 7000 [size=64]
I/O ports at 7080 [size=16]
I/O ports at 70c0 [size=16]
I/O ports at 7400 [size=4]
I/O ports at 7440 [size=4]
Capabilities: <available only to root>

Thks for all the help you can give me.

[rickenbacherus]

This card works beautifully with Linux & Knoppix. I just so hapen to have one. Try using the alsa cheat code. If that doesn't get it I would suspect an IRQ conflict or some other configuration problem.

cat /proc/interrupts

might tell you something. Also have a look through dmesg to see what there is to see. Post the output of lsmod please.

[Syslog]

Thks once again for the quick reply.

Here's what you ask:
Linux version 2.4.20-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian pre
release)) #1 SMP Mit Mär 26 15:37:36 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda3 ro vga=791 apm=power-off hda=scsi hdb=scsi h
dc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi nomce BOOT_IMAGE=vmlinuz al
sa
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 848.252 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1690.82 BogoMIPS
Memory: 256504k/262080k available (1270k kernel code, 5188k reserved, 503k data,
128k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 0a
per-CPU timeslice cutoff: 731.31 usecs.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7110] at 00:02.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0x81000000, mapped to 0xd080d000, size 8128k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:50e2
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 11
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x9040-0x9047, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x9048-0x904f, BIOS settings: hdcio, hddio
hda: IBM-DJSA-220, ATA DISK drive
hdc: MATSHITA CR-177, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 39070080 sectors (20004 MB) w/1874KiB Cache, CHS=2432/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
Partition check:
hda: hda1 hda2 hda3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: CD-ROM CR-177 Rev: 7T03
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 128k freed
Adding Swap: 192772k swap-space (priority -1)
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:09.0
PCI: Sharing IRQ 11 with 00:09.1
PCI: Found IRQ 11 for device 00:09.1
PCI: Sharing IRQ 11 with 00:09.0
Yenta IRQ list 0698, PCI irq11
Socket status: 30000007
Yenta IRQ list 0698, PCI irq11
Socket status: 30000c11
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:50:01 Mar 26 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:02.2
usb-uhci.c: USB UHCI at I/O 0x9000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Serial driver version 5.05c (2001-07-0 with MANY_PORTS SHARE_IRQ SERIAL_PCI IS
APNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PCI: Found IRQ 5 for device 00:06.1
PCI: Sharing IRQ 5 with 00:06.0
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (11c1,0447,1468,0440)
and the manufacturer and name of serial board or modem board
to [email protected].
register_serial(): autoconfig failed
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.
html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@sa
w.sw.com.sg> and others
PCI: Found IRQ 5 for device 00:06.0
PCI: Sharing IRQ 5 with 00:06.1
eth0: OEM i82557/i82558 10/100 Ethernet, 000:59:3E:35:4D, IRQ 5.
Board assembly 60082c-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
solo1: version v0.19 time 15:49:36 Mar 26 2003
PCI: Found IRQ 5 for device 00:08.0
PCI: Sharing IRQ 5 with 01:00.0
solo1: joystick port at 0x7441
solo1: ddma base address: 0x70c0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe0000000
blk: queue c032bfc4, I/O limit 4095Mb (mask 0xffffffff)
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
hermes.c: 5 Apr 2002 David Gibson <[email protected]>
orinoco.c 0.11b (David Gibson <[email protected]> and others)
orinoco_cs.c 0.11b (David Gibson <[email protected]> and others)
eth1: Station identity 001f:0009:0001:0004
eth1: Looks like an Intersil firmware version 1.04
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:6F:04:A9:03
eth1: Station name "Prism I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 3, io 0x0100-0x013f
eth1: Error -110 setting multicast list.
eth1: Error -110 setting multicast list.
eth1: Error -110 writing Tx descriptor to BAP
parport0: PC-style at 0x378 [PCSPP]
lp0: using parport0 (polling).
lp0: console ready
eth1: Error -110 setting multicast list.
eth1: Error -110 writing Tx descriptor to BAP
hermes.c: 5 Apr 2002 David Gibson <[email protected]>
orinoco.c 0.11b (David Gibson <[email protected]> and others)
orinoco_cs.c 0.11b (David Gibson <[email protected]> and others)
eth1: Station identity 001f:0009:0001:0004
eth1: Looks like an Intersil firmware version 1.04
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: Station name "Prism I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 3, io 0x0100-0x013f
eth1: Error -110 setting multicast list.


About alsa, i'm noob in this and i don't now how to put alsa working, can you tell me how?!

Thks again.