-

Originally Posted by
champagnemojo
First of all, really nice instructions. I still don't completely understand the LILO step to load the 2.4 kernel. All you had to do was run /sbin/lilo -v without any changes to lilo.conf and it was set back to boot 2.4? Or did you have to uncomment the two lines that Stephen mentioned? I might install it again using both of your instructions...if nothing else, for a learning experience.
Also, do you notice a big improvement with the 2.6 kernel? I can't get my netcard working on my 2.6 install, but I've messed around with it a little. I noticed that it booted quicker. Are there other benefits you've noticed?
I did not have to uncomment out those lines Stephen mention. doing a more /install-drive/etc/lilo.conf both the prompt and timeout commands were already live (i.e. not commented out) by default. Stephen mentioned that he DID need to uncomment/add those lines. good rule of thumb use the mroe command, if those lines are in lilo.conf leave em alone. if not uncomment or add them as the case dictates. Basically you boot into LinuxOLD (2.4 kernel) after installation becase the initrd image created was "bad". you boot into LinuxOLD just long enough to create a workign one, edit lilo.conf to point to the working initrd you just made then rebbot and 2.6.1 works.
As for your network card is it supported by the 2.6.x kernel? I'm assuming you do have module-init-tools installed, if nto installing that might help. If your card is supported by the kernel AND loading the netcard driver as a module doesn't work try recompiling the kernel and selecting Y instead of M for yoru network card. Or do a google search on linux 2.6 and the name of your network card, see if there's anything that's been posted about it.
I must concurr with Stephen on the improvements in the 2.6 kernel, everything runs much faster, ALSA for lack of a better term "just works" which is something I was losing the battle to in the 2.4 kernel. my USB 2.0 card is now recognized, there's built in support now for PS2 mice.. lots of fun stuff, give it a whirl
Similar Threads
-
By eraserman in forum General Support
Replies: 4
Last Post: 11-04-2004, 07:43 AM
-
By dmpop in forum The Lounge
Replies: 0
Last Post: 10-13-2004, 02:32 PM
-
By Sk83r99 in forum General Support
Replies: 3
Last Post: 08-17-2004, 12:38 AM
-
By naventus in forum Hdd Install / Debian / Apt
Replies: 22
Last Post: 07-17-2004, 05:05 AM
-
By Raj in forum Customising & Remastering
Replies: 1
Last Post: 02-19-2003, 01:19 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules

Lot of 500 Cisco 10-3145-02 QSFP-100G-CWDM4-S 100G CWDM4 QSFP28 Transceiver
$1500.00

Cisco WS-C3650-12X48UR-L 48-Port Stackable Layer 3 8x10G SFP+ Port Switch
$129.99

Cisco C9300NM8X Network Switch Module
$599.99

Cisco WS-C3850-12X48U-S 48-Port UPoE Switch 1100W PSU
$149.99

Cisco C9300-48UXM-A Switch 9300 Series 48-port UPoE Network
$874.99

Cisco Catalyst C9120AXI-B Wi-Fi 6 Access Points
$36.00

Cisco Catalyst WS-C3560CX-8PC-S Managed Switch 8 PoE+ Port | Quantity Available
$97.49

Cisco C3850-NM-2-10G Catalyst 3850 2 x 10GE Network Module
$30.00

Cisco Catalyst C9130AXI-B WiFi 6 802.11ax Wireless Access Point Brand New
$101.99

NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$24.00