Are You able to get into w$?
i installed knoppix to my seagate baracuda 160gb, on a 10gb partition, but it refused to boot. i could select windows or linux from LILO, but when i choose either, it just gave ma a blank screen.
So i formatted the disk again, but when i rebooted, it said the hdd was 0gb, and its name had changed from ST3160021A to ST>1<0<2!! or something similar... and now nothing can read the hdd. Any ideas? could it have been knoppix that did this? thanks either way
Are You able to get into w$?
w$?
Sorry... Windows.
no nothing can read/write the drive....
also, the only way i can boot knoppix is to disconnect the hdd, as knoppix crashes on startup when it tried to search the hdd for a home directory or sumething like that
iirc, some drives that are big have a parrtition which has something the disk needs to work properly, thats all i can say.
Does this mean that KNOPPIX delete that partition?
It sounds strange; usually linux is know to be very respecfull of data.
No but the problem is with the new 2.6 kernel. Your partition table is corrupted and can be repaired as adviced in SUSE's page http://portal.suse.com/sdb/en/2004/0...booting91.htmlOriginally Posted by georgewh
The problem is that the BIOS and Linux 'see' different disk geometries AND The Windows partition is > 8 GB. Activate LBA from BIOS and check that hard disk value IS NOT set to AUTO.
-tapsa-
i tried this, but when i add the 'driver update' for the suse installation, it sees the hdd as 160gb, and says that the partition table is 'OK', and doesnt change anything, however, it wont install, as it says its unable to create partition hda2.Originally Posted by tr
when i reboot, it detects the name correctly, but after i try to access the drive, it becomes unreadable again
also, the 'auto' setting in my bios has always worked correctly before, with LBA enabled. the only other setting i have in the bios is 'auto, disabled, cdrom', so i have no choice
but thanks for your help anyway!
[quote]: also, the 'auto' setting in my bios has always worked correctly before, with LBA enabled. the only other setting i have in the bios is 'auto, disabled, cdrom', so i have no choice.
Did You clik "ENTER" when You scroll between "AUTO CDROM DISABLE"? If not You have to do this after You see "AUTO".
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$95.00
Lot (10) Dell 0N8TDR 850nm SFP-10G-SR-85C 10Gbs sfp+ FTLX8574D3BNL-FC N8TDR NEW
$68.00
ProLabs 10GBase-TX SFP+ RJ-45 Copper Transceiver Module P/N: SFP-10GBASE-T-C NEW
$34.99
New HP Aruba J9150D 10GBASE-SR SFP+ Transceiver Module
$35.88
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$10.99
Lot of 10 - HP 10Gb SR SFP+ Transceiver 455883-B21 455885-001 456096-001 850nm
$25.99
Genuine Cisco SFP-10G-SR Transceiver Module (10-2415-03)
$5.85
Cisco Nexus 96-Port 10G SFP+ Switch N9K-93128TX w/ 9K-M12PQ 12-Port 40G QSFP
$149.99
New Sealed Cisco SFP-10G-LR 10GBASE-LR SFP Plug-in GBIC Transceiver module A
$15.80