I found this thread posted by philo on 08-09-2014:
Time zone change cannot be made permanent.
I can set the time zone and it shows correct in /etc/timezone "America/Vancouver".
After reboot /etc/timezone is overwritten and says "localtime"
More Help needed:
Time and Day Settings:
I live in Time zone America/Vancouver. After each reboot the Time zone is reset to local time which is my time +8 hours.
Where is the configuration file for Time and Day Settings to find?
I might be able to change "local" to "America/Vancover" ?
I found this thread posted by philo on 08-09-2014:
Time zone change cannot be made permanent.
I can set the time zone and it shows correct in /etc/timezone "America/Vancouver".
After reboot /etc/timezone is overwritten and says "localtime"
I entered UTC in /etc/adjtime and set the time zone again to America/Vancouver.
After reboot /etc/adjtime was still ok (UTC) but /etc/timezone was again "localtime".
What to do?
BIOS time (hardware clock) --> UTC
/etc/adjtime --> UTC [instaead of LOCAL]
/etc/timezone ---> America/Vancouver
and maybe in :
/media/sd__/boot/syslinux/syslinux.cfg
LABEL knoppix LABEL knoppix64, add inside APPEND:
--> tz=America/Vancouver
To 1):
The BIOS is for MSI motherboard 785GM-E51.
I can not change the time - it shows +7 hours from my local time.
To 2):
Ihave changed this to UTC!
To 3):
Ihave changed this to America/Vancouver - but it is mysteriously overwritten to America/New-York
To 4):
root@Microknoppix:/# sudo nano /media/sdg/boot/syslinux/syslinux.cfg
/media/sdg/boot/syslinux/syslinux.cfgdoes not exist
root@Microknoppix:/# ls
config-4.12.7 grub ipxe.lkrn System.map-4.12.7-64 vmlinuz-4.12.7
config-4.12.7-64 ipxe.efi System.map-4.12.7 vmlinuz vmlinuz-4.12.7-64
I just run this script automatically on boot (see https://wiki.lxde.org/en/Autostart). Good enough for me. Change the 2nd line as needed.
time=$(date +%Y%m%d\ %H:%M:%S)
echo Europe/Amsterdam | sudo tee /etc/timezone
sudo dpkg-reconfigure -f noninteractive tzdata
sudo date --set="$time"
sudo hwclock --systohc
You could even add something like:
(sleep 60 && sudo rdate -n pool.ntp.org && sudo hwclock --systohc) &
I found syslinux.cfg in >Root >KNOPPIX >boot and added
inside APPEND: -->tz=America/Vancouver
Now, in window under ---> Preferences ---> Time and Date the line 'Time zone' is filled in correctly (America/Vancouver) and the line 'Configuration' is filled in correctly (Keep synchronized with Internet servers) as well.
I still don't get the PST (Pacific Standard Time) though. Only if I switch the configuration back and forth between 'Manual' and '...synchronized...' then, after a few minutes, the PST is shown....
What else is missing?
Last edited by Karibu; 10-14-2017 at 02:53 AM. Reason: more text
Cisco SFP-10/25G-CSR-S 10/25GBASE-CSR SFP28, 850nm, 100m, LC,
$54.00
Cisco SFP-10G-LR-S 10GBASE-LR SFP+, 1310nm, 10km, LC, SMF
$27.00
Cisco SG110 24 Port Gigabit Ethernet Switch w/ 2 x SFP SG110-24
$117.00
Cisco SFP-25G-SR-S 25GBASE-SR SFP28, 850nm, 100m, LC, MMF
$54.00
NEW FS SFP-10G-T 10GBASE T SFP+ 30M Transceiver Module (Lot of 1)
$39.95
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$89.00
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$13.89
New Cisco w/ Green Hologram SFP-25G-SR-S 25G SFP28 SR 850nm 300m LC MMF Module
$69.99
New Cisco w/ Green Hologram SFP-10G-LR-S 10G SFP+ LR 1310nm 10km SMF LC Module
$34.99