Check out the Cheat Codes for optional bootup switches.
http://knoppix.net/wiki/Cheat_Codes
I have a 64-bit processor on a Dell 9360 machine.
If I boot into Knoppix 8.2.0 Live from a portable drive and run simple queries as follows I get:
$ lscpu
Architecture: x86_64
CPU op-mode(s): 32 bit,64 bit
Flags: ... lm ...
$ lshw -C processor | grep width
width: 64 bits
$ grep flags /proc/cpuinfo | grep " lm "
Flags: ... lm ...
which all confirm the 64-bit architecture. BUT the response
CPU op-mode(s): 32 bit,64 bit
apparently indicates that I am running a 64-bit-capable machine in 32-bit-mode.
Yes? - is this a true interpretation?
My /boot/isolinux/isolinux.cfg file contains the lines (omitting redundant qualifiers for ease of reading)
DEFAULT fergus
LABEL fergus
KERNEL ifcpu64.c32
APPEND knoppix64 -- knoppix
APPEND knoppix64
LABEL knoppix
KERNEL linux
APPEND initrd=minirt.gz
LABEL knoppix64
KERNEL linux64
APPEND initrd=minirt.gz
which I hoped meant "if 64-bit machine use 64-bit OS; if 32-bit machine use 32-bit OS" but apparently not.
How can I tweak the isolinux.cfg file to behave as required one line up?
Thank you!
PS1 I have to admit (I have only just noticed) that the file ifcpu64.c32 referred to above is very suggestive of an instruction "if 64-bit machine use 32-bit OS". Is that what it achieves, and the cause of the mismatch described?
PS2 I use this ifcpu file from the Knoppix 7.4.2 provision. I find the Knoppix 8.2.0 version stops Knoppix stone dead before it even starts. It simply does not work, at all. Anybody else?
Check out the Cheat Codes for optional bootup switches.
http://knoppix.net/wiki/Cheat_Codes
NEW Sealed Cisco SFP-10G-LR 10GBASE-LR SFP+ 1310nm 10km *US Shipping*
$18.00
New Cisco SFP-25G-SR-S 25G SFP28 25GBASE-SR 850nm 300m LC MMF Transceiver Module
$51.30
LOT OF 10 455883-B21 HP 10Gb SR SFP Transceiver 455885-001 456096-001
$59.99
Cisco Nexus 48-Port 10G SFP+ Switch N9K-93128TX w/ 9K-M12PQ 12-Port 40G QSFP
$112.49
GENUINE Cisco SFP-10G-SR V03 SFP+ GBIC Transceiver Module 10-2415-03
$6.80
🔥🔥🔥 CISCO SFP-10G-SR V03 10-2415-03 850nm 10GBASE-SR SFP+ Multi Module 🔥🔥🔥
$6.80
CISCO C3850-NM-4-10G 4-Port 10Gb SFP NETWORK EXPANSION MODULE
$110.00
NEW FS SFP-10G-T 10GBASE T SFP+ 30M Transceiver Module (Lot of 1 Unit)
$39.95
New Cisco GLC-TE 1G SFP Copper RJ45 100m 1000BASE-T Transceiver Module
$22.32
For Cisco SFP-10G-T, Ubiquiti UF-RJ45-10G Transceiver, SFP+ to RJ45 10GBase-T
$45.99