knoppix 3.4 kernel 2.6 ethernet help!

[secknet]

Hi i'm italian and sorry for my english!
I have a problem: i installed knoppix 3.4(the last) on my hard disk and works fine but my network connection doesen't work.
I have two ethernet card, one is sis 900(integrated) and one is realtek 8139 .
When is set the netowrk parameters not works , wich ifconfig from shell is the same!
I see if the module is ok but lsmod: no module installed for sis and for realtek.
Which modprobe the module is loaded but not working the network connection!!!
This problem only if i start knoppix with kernel 2.6.6 and the kernel boot report that i have 3 ethernet interfaces!!! i have two.
with kernel 2.4.26 is ok but when i shut down knoppix and restart i lose network configuration and is necessary to rewrite the configuration!
Anyone can explain to me to solve the problem with kernel 2.6.6?
And which method can i use to save a configuration of network card without rewrite all any moment?

Thanks in advance

[user unknown]

You may not use the modules for 2.4.x with 2.6.y, nor may you keep the driver during reboot.

The 2.6.y - drivers are located in /lib/modules/2.6.y/... and
the 2.4.x - drivers are located in /lib/modules/2.4.x/...

They aren't compatible.

If you enter: ifconfig eth0 or ifconfig eth1, what do you get?

And do you have a module 8139too.ko?

if you modprobe 8139too, what is the result of lsmod | grep 8139

[turbines]

I have connection problem with 3.4 too.

I am running Knoppix 3.4 on HDD. When I first boot I have no connection.

lsmod and ifconfig gives the following;

lsmod gives
root@knopbox:~# lsmod
Module Size Used by Not tainted
raw1394 19252 0 (unused)
ehci-hcd 16616 0 (unused)
autofs4 8756 1
af_packet 13544 0
nls_iso8859-1 2844 0
nls_cp437 4348 0
agpgart 42660 0 (unused)
i810_audio 25208 1
ac97_codec 11884 0 [i810_audio]
3c59x 25456 0 (unused)
forcedeth 9836 1
tuner 9408 1 (autoclean)
tvaudio 12444 0 (autoclean) (unused)
bttv 96320 0 (unused)
i2c-algo-bit 6920 1 [bttv]
i2c-core 12228 0 [tuner tvaudio bttv i2c-algo-bit]
soundcore 3428 2 [i810_audio bttv]
videodev 5600 2 [bttv]
serial 52068 0 (unused)
joydev 7584 0 (unused)
hid 22372 0 (unused)
input 3168 0 [joydev hid]
sbp2 16588 0 (unused)
usb-storage 61952 0
ataraid 6404 0 (unused)
ohci1394 22888 0 (unused)
ieee1394 183300 0 [raw1394 sbp2 ohci1394]
usb-ohci 18088 0 (unused)
usbcore 57824 1 [ehci-hcd hid usb-storage usb-ohci]
pcmcia_core 39840 0
thermal 6532 0 (unused)
processor 8976 0 [thermal]
fan 1568 0 (unused)
button 2508 0 (unused)
battery 5888 0 (unused)
ac 1792 0 (unused)
ide-cd 28704 0
ide-scsi 9040 0
rtc 7004 0 (autoclean)
ext3 64452 1 (autoclean)
jbd 46516 1 (autoclean) [ext3]


I am running Knoppix 3.4 on HDD. When I first boot I have no connection and ifconfig gives the following;

root@knopbox:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:E0:18F:B1:36
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:590 (590.0 b) TX bytes:342 (342.0 b)
Interrupt:20 Base address:0x1000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:10 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:500 (500.0 b) TX bytes:500 (500.0 b)

The I go to the Knoppix Network Card configuration and select eth0 and yes to DHCP. I am then connected OK and ifconfig gives the following;

root@knopbox:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:E0:18F:B1:36
inet addr:192.168.100.11 Bcast:192.168.100.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:349 errors:0 dropped:0 overruns:0 frame:0
TX packets:407 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:139191 (135.9 KiB) TX bytes:70000 (68.3 KiB)
Interrupt:20 Base address:0x1000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:700 (700.0 b) TX bytes:700 (700.0 b)

When I reboot my connection is gone again

I have seen some threads hinting that all this may be caused by windows security updates but that is sure hard to believe.

[turbines]

I just ran both 3.3 and 3.4 booting from CD and both still configure internet connection through my eth0 automatically. Something has happened during the HDD install

[user unknown]

Are you sure, that the dhcp-setup is correct?
Running netconfig every time is no solution. The networkcard is found, as you see, it only lacks an inet adress.

You may set it manually like this:

ifconfig eth0 192.168.100.11 up

[turbines]

I am a noob and I don't have a clue as how to determine if dhcp is set up properly. Can you help me with that.

I know that when I select eth0 from the Knoppix network card configuration and then click on OK for dhcp broadcasting it has no problem finding the IP address and it then connects immediately

[user unknown]

My first question is: Who serves that ip-adress?
Is it a different PC, or a device like a dsl-modem?

I have an mini-lan: one desktop and one, sometimes two laptops.
And a dsl-modem to connect to the internet.

From the dsl-modem, I get an ip-adress for ppp-usage.
But I still have a lan-adress for the same network-card (192.168.0.3).

For a small lan, an dhcp-server is overkill - just set a static ip in your initscripts.

[turbines]

The IP is the static IP chosen for the local PC that Knoppix is running on

[user unknown]

And why do you want to use dhcp? 'd' means 'dynamic' which is the opposite of 'static'.

get root,
write a script /etc/rc4.d/S50ipup.sh:

# 
# (c) turbines 2004
#
ifconfig eth0 192.168.100.11 up

make it executable.

voila.

[turbines]

root@knopbox:~# /etc/rc4.d/S50ipup.sh:
bash: /etc/rc4.d/S50ipup.sh:: No such file or directory