Results 1 to 7 of 7

Thread: DHCP

  1. #1
    Senior Member
    Join Date
    Jul 2011
    Posts
    110

    DHCP

    Im booting Knoppix 6.7 via pxe. Once Knoppix starts to load I get delay in DHCP during boot. The sending dhcp message appears for quiet some time. Then knoppix goes about its boot. The unit has an ip from the pxe process. So my question is, is this a knoppix delay or my pxe server? Any ideas?
    Thanks!

  2. #2
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    FWIW, no significant delay in normal (not pxe) use of dhcp.

  3. #3
    Senior Member
    Join Date
    Jul 2011
    Posts
    110
    So called normal use of DHCP within Knoppix doesnt begin until after X has started/loaded. Knoppix needs IP before X when pxe booting. I think it may be within minirt.gz the ini file itself. ?

  4. #4
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    I've contributed all I know for sure on this.
    But if pxe needs IP early, why isn't the server providing it already?

    Are you able to decode minirt.gz and read the init?

  5. #5
    Senior Member
    Join Date
    Jul 2011
    Posts
    110
    Yes, Ive just started to dig thru ini. I think DHCP server is confused by knoppix asking for an ip from the same mac addy that just requested ip?

  6. #6
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    FWIW,

    In 6.4.4 my LiveUSB took almost 120 seconds to get on-line initially.
    I finally disabled Network Manager and got down to about 55-or so seconds
    using a primitive /etc/rc.local routine to get my wifi going.

    In 6.7, there was no similar slow start to getting on-line in less than
    a minute and no need to circumvent Network Manager.

    Obviously either Knoppix or Network Manager must have changed between
    6.4.4 and 6.7. If you don't find the answer in minirt.gz, then you might
    see if there's some difference in NM that explains your situation.

  7. #7
    Senior Member
    Join Date
    Jul 2011
    Posts
    110
    Thanks for those ideas. I will post my findings. May take me a few days.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Supermicro SuperServer E300-15 - SYS-e300-9C - 16GB RAM 240GB Samsung SSD picture

Supermicro SuperServer E300-15 - SYS-e300-9C - 16GB RAM 240GB Samsung SSD

$199.99



HP Proliant MicroServer Gen 8 2.23GHz Xeon 16GB RAM NO SSD picture

HP Proliant MicroServer Gen 8 2.23GHz Xeon 16GB RAM NO SSD

$249.99



Supermicro 505-2   Server picture

Supermicro 505-2 Server

$280.00



Nasuni NF-50 Supermicro Server, Atom CPU C2558, @ 2.40GHz, 8GB RAM-No HDD/OS/AC picture

Nasuni NF-50 Supermicro Server, Atom CPU C2558, @ 2.40GHz, 8GB RAM-No HDD/OS/AC

$250.00



Supermicro 2U X10DRU-i 2x E5-2680 v3 2.5ghz 32gb Ram  240gb SSD 2x GPU *READ* picture

Supermicro 2U X10DRU-i 2x E5-2680 v3 2.5ghz 32gb Ram 240gb SSD 2x GPU *READ*

$369.99



New Barebones Supermicro 5019D Server, 4C/8T Xeon D-2123T, 1U Rackmountable, 10G picture

New Barebones Supermicro 5019D Server, 4C/8T Xeon D-2123T, 1U Rackmountable, 10G

$449.99



SuperMicro 4U CSE 847 36 Bay LFF Barebone 2x 1280W w/ 2x Bays 2.5 Rear w/Trays picture

SuperMicro 4U CSE 847 36 Bay LFF Barebone 2x 1280W w/ 2x Bays 2.5 Rear w/Trays

$499.99



Supermicro 5019D-4C-FN8TP Xeon D-2123IT (4C/8T) 64GB DDR4 10GbE 480GB 1U Server picture

Supermicro 5019D-4C-FN8TP Xeon D-2123IT (4C/8T) 64GB DDR4 10GbE 480GB 1U Server

$689.00



Supermicro CSE-937 3U Storage Chassis No CPU No HDD No Ram Tested & Reset picture

Supermicro CSE-937 3U Storage Chassis No CPU No HDD No Ram Tested & Reset

$129.99



Supermicro E300-12C Mini 1U Barebone X12SCV-LVDS LGA1200 SNK-P0073A4 w/ Adapter picture

Supermicro E300-12C Mini 1U Barebone X12SCV-LVDS LGA1200 SNK-P0073A4 w/ Adapter

$225.00