Somebody else asked this recently, see http://www.knoppix.net/forum/viewtopic.php?t=15751
after i installed knoppix v3.7 on hdd then after reboot it then gives me boot menu then after i enter the specified menu then it gives me this error :
initrd-tools : 0.1.74
mount : fs type devfs not supported by kernel
umount : devfs : not mounted
mount : fs type devfs not supported by kernel
umount : devfs : not mounted
pivot_root : No such file or directory
/sbin/init : 426 : cannot open dev/console : no such file
Kernel panic : Attempted to kill init!
and the lights of the caps and scroll lock keeps on blinking then it stay's there for about 30mins .. and i assume it hangs.
Somebody else asked this recently, see http://www.knoppix.net/forum/viewtopic.php?t=15751
the forum site u gave me give no results? any possible solution out there?
Could be a bad burn or bad download. Try burning again with a slower speed. Then when you boot at the prompt type knoppix testcd, that check the integrity of the files of the cd. Good luck.
That's because there aint no answer!Originally Posted by twistedalpha
The URL I referenced above was me asking the same question about the same problem along with another guy. I've seen this problem since Knoppix v3.6. I've also seen the same problem on the most recent 2 versions of Kanotix. What I am saying is that I think it is a bug in the latest Debian unstable libparted and, unfortunately, we have to wait until Debian fixes it.
rrfish72, this exactly the same problem experienced by quite a few people. It is *not* due to a bad burn/download etc. It occurs only with the very latest Knoppix/Kanotix/Mepis/Unstable (etc) and only with some newer motherboards.Originally Posted by rrfish72
Why not post this in the kanotix forum and maybe Kano will get you the answer.
http://kanotix.mipooh.net/
I don't really know anything about this problem and I'm not disputing what you are saying, but do I understand right that this problem is only seen after a hard disk install but not off the live CD? If so, how is it a bug in the latest Debian unstable libparted? I just don't understand why that would be.Originally Posted by markb
Oh well so much for v3.7 ..
I've used and installed 3.7 successfully three times on 3 different computers. Might be just operator error!
Lot (10) Dell 0N8TDR 850nm SFP-10G-SR-85C 10Gbs sfp+ FTLX8574D3BNL-FC N8TDR NEW
$68.00
New HP Aruba J9150D 10GBASE-SR SFP+ Transceiver Module
$35.88
ProLabs 10GBase-TX SFP+ RJ-45 Copper Transceiver Module P/N: SFP-10GBASE-T-C NEW
$34.99
Cisco Nexus 96-Port 10G SFP+ Switch N9K-93128TX w/ 9K-M12PQ 12-Port 40G QSFP
$149.99
Genuine Cisco SFP-10G-SR Transceiver Module (10-2415-03)
$5.85
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$10.99
Netgear 16-Port Gigabit Ethernet Switch GS316 Unmanaged
$10.00
LOT OF 10 HPE JD092B X130 10G SFP+ LC SR Transceiver
$40.00
HP Aruba J4859D 1000BASE-SX SFP Transceiver Module - Brand New
$17.00