Results 1 to 7 of 7

Thread: DHCP

  1. #1
    Senior Member
    Join Date
    Jul 2011
    Posts
    110

    DHCP

    Im booting Knoppix 6.7 via pxe. Once Knoppix starts to load I get delay in DHCP during boot. The sending dhcp message appears for quiet some time. Then knoppix goes about its boot. The unit has an ip from the pxe process. So my question is, is this a knoppix delay or my pxe server? Any ideas?
    Thanks!

  2. #2
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    FWIW, no significant delay in normal (not pxe) use of dhcp.

  3. #3
    Senior Member
    Join Date
    Jul 2011
    Posts
    110
    So called normal use of DHCP within Knoppix doesnt begin until after X has started/loaded. Knoppix needs IP before X when pxe booting. I think it may be within minirt.gz the ini file itself. ?

  4. #4
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    I've contributed all I know for sure on this.
    But if pxe needs IP early, why isn't the server providing it already?

    Are you able to decode minirt.gz and read the init?

  5. #5
    Senior Member
    Join Date
    Jul 2011
    Posts
    110
    Yes, Ive just started to dig thru ini. I think DHCP server is confused by knoppix asking for an ip from the same mac addy that just requested ip?

  6. #6
    Senior Member registered user
    Join Date
    May 2006
    Location
    Columbia, Maryland USA
    Posts
    1,631
    FWIW,

    In 6.4.4 my LiveUSB took almost 120 seconds to get on-line initially.
    I finally disabled Network Manager and got down to about 55-or so seconds
    using a primitive /etc/rc.local routine to get my wifi going.

    In 6.7, there was no similar slow start to getting on-line in less than
    a minute and no need to circumvent Network Manager.

    Obviously either Knoppix or Network Manager must have changed between
    6.4.4 and 6.7. If you don't find the answer in minirt.gz, then you might
    see if there's some difference in NM that explains your situation.

  7. #7
    Senior Member
    Join Date
    Jul 2011
    Posts
    110
    Thanks for those ideas. I will post my findings. May take me a few days.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


MITS Altair 680 Case Only LAST ONE LS3 picture

MITS Altair 680 Case Only LAST ONE LS3

$500.00



Bare S100 CPU Replacement for ALTAIR 8800 IMSAI 8080 JAIR Single Board Computer picture

Bare S100 CPU Replacement for ALTAIR 8800 IMSAI 8080 JAIR Single Board Computer

$42.00



MITS Altair 8800 Computer Bamboo  Reproduction Arduino Tested Working Assembled  picture

MITS Altair 8800 Computer Bamboo Reproduction Arduino Tested Working Assembled

$649.99



MITS ALTAIR 8800  Original Vintage Microcomputer picture

MITS ALTAIR 8800 Original Vintage Microcomputer

$6000.00



S-100 backplane motherboard bare PCB 9 slot (for Altair/IMSAI) picture

S-100 backplane motherboard bare PCB 9 slot (for Altair/IMSAI)

$30.00



MITS ALTAIR 8800  Original Vintage Microcomputer with 14 boards - Buy It Now picture

MITS ALTAIR 8800 Original Vintage Microcomputer with 14 boards - Buy It Now

$9500.00



MITS ALTAIR 8800  Original Vintage Microcomputer  S-100   Buy It Now $5999 picture

MITS ALTAIR 8800 Original Vintage Microcomputer S-100 Buy It Now $5999

$5999.00



Altair MITS 8800 CPU Parts Kit not IMSAI 8080 S100 (board NOT included) picture

Altair MITS 8800 CPU Parts Kit not IMSAI 8080 S100 (board NOT included)

$64.95



Vintage Altair 8088 CPU Wire Wrapped S100 Card w Mon EPROM circuit board #T71 picture

Vintage Altair 8088 CPU Wire Wrapped S100 Card w Mon EPROM circuit board #T71

$99.00



VINTAGE DEC 1975 VOL 1 ISSUE 1 SCCS INTERFACE MAGAZINE MITS ALTAIR COVER & ADS picture

VINTAGE DEC 1975 VOL 1 ISSUE 1 SCCS INTERFACE MAGAZINE MITS ALTAIR COVER & ADS

$359.99