Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Cannot set static IP address in Knoppix 7

  1. #1
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9

    Question Cannot set static IP address in Knoppix 7

    I often boot to Knoppix 2 (the command-line) on a network without DHCP that I administer. Up through Knoppix 6, I always set a static IP address by appending the following to /etc/network/interfaces:

    auto eth0
    iface eth0 inet static
    address 10.0.0.200
    netmask 255.255.255.0
    gateway 10.0.0.1

    Then, I would bring it up:

    ifup eth0
    portmap (I now am using "rpcbind" instead since portmap is renamed in Knoppix 7)
    rpc.statd


    This has always worked for me the in the past using pre-version 7 Knoppix and portmap. Now it works, but only for 15 seconds or so before the interface falls down. Both the presence of an IPv4 address in "ifconfig" and pinging reveal that. I can even bring eth0 up and "ping -c 40 10.0.0.1", then watch it ping successfully the first few times and get some "address not routable" error thereafter!

    I've also tried the boot cheats "nodhcp" and "ip=10.0.0.200" to no avail. Is my procedure for static IPs out of date? Or have I encountered a bug in Knoppix 7?

  2. #2
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    I haven't needed static IP for years, but this could look like some network-manager stuff to me. Tried to halt or setup the network manager?

  3. #3
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    Where do I find network manager? Is that a graphical program? If so, it shouldn't affect anything in text mode (Knoppix 2).

    I did boot to the GUI and set the static IP address graphically and it worked, BTW. But that's not a solution to my problem because I still prefer text mode and should be able to change network adapter settings from there.

  4. #4
    Senior Member registered user
    Join Date
    Feb 2010
    Posts
    512
    Did you try the cheatcode 'nonetworkmanager'?

  5. #5
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    Quote Originally Posted by voidxor View Post
    Where do I find network manager? Is that a graphical program? If so, it shouldn't affect anything in text mode (Knoppix 2).

    I did boot to the GUI and set the static IP address graphically and it worked, BTW. But that's not a solution to my problem because I still prefer text mode and should be able to change network adapter settings from there.
    All system programs may be equipped with some kind of graphical front-ends, but still operate without them, so text mode is no guarantee that a service doesn't run and keep on doing things you don't want. If you search for network-manager, you will find it is a Gnome-based service, currently configured by /etc/NetworkManager/NetworkManager.conf (on my out-of-the-box 7.0.5 DVD), with this default content:

    Code:
    [main] 
    plugins=ifupdown,keyfile  
    [ifupdown]
    managed=true
    The intention, at least, is that you can tweak this to fit your needs, but if it doesn't wotk out, you can always use the cheat code klaus2008 suggests.

  6. #6
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    The nonetworkmanager cheat works perfectly. Thank you for the workaround. Are we gaining a consensus that Network Manager is unwelcome in Knoppix 2? Does anybody else feel that this is a bug?

  7. #7
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    Quote Originally Posted by voidxor View Post
    The nonetworkmanager cheat works perfectly. Thank you for the workaround. Are we gaining a consensus that Network Manager is unwelcome in Knoppix 2? Does anybody else feel that this is a bug?
    I wouldn't call it a bug with today's ordinary uses. To me, it is rather a typical example of simplicity for most users becoming a hassle for some more technically oriented ones. I think the config files lets us give the MAC addresses of interfaces network-manager shall keep its fingers off, so it should be a rather simple configuration operation once one knows about it.

  8. #8
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    Quote Originally Posted by Capricorny View Post
    I wouldn't call it a bug with today's ordinary uses. To me, it is rather a typical example of simplicity for most users becoming a hassle for some more technically oriented ones.
    Specifically, I meant that Network Manager is helpful to most users (who boot to the GUI). I only meant that it is unwelcome in Knoppix 2 (the text-mode). Since the default content of /etc/NetworkManager/NetworkManager.conf that you pasted above doesn't have an obvious spot for a static IP address, subnet mask, and default gateway, I find /etc/network/interfaces to be the obvious way to establish a static IP address in text mode. Therefore, I don't welcome Network Manager when booted to text mode. Furthermore, I believe Knoppix 7's command line should behave as close to Knoppix 6's command line as possible. New features shouldn't break beloved commands.

  9. #9
    Senior Member registered user
    Join Date
    Sep 2006
    Posts
    802
    Quote Originally Posted by voidxor View Post
    Specifically, I meant that Network Manager is helpful to most users (who boot to the GUI). I only meant that it is unwelcome in Knoppix 2 (the text-mode). Since the default content of /etc/NetworkManager/NetworkManager.conf that you pasted above doesn't have an obvious spot for a static IP address, subnet mask, and default gateway, I find /etc/network/interfaces to be the obvious way to establish a static IP address in text mode. Therefore, I don't welcome Network Manager when booted to text mode. Furthermore, I believe Knoppix 7's command line should behave as close to Knoppix 6's command line as possible. New features shouldn't break beloved commands.
    Yes, in your use situation, the case is pretty clear. But I can imagine that KK is rather reluctant to tie basic services to the graphical mode, which is why he has opted for a cheatcode off-switch instead. And when you have told networkmanager not to manage an interface, I would think the other configuration tools work or could relatively easily be made to do so.

    I completely agree with respect to command line behavior.

  10. #10
    Junior Member voidxor's Avatar
    Join Date
    Jan 2013
    Location
    Kansas
    Posts
    9
    Update: I have solved my static IP troubles by switching to Debian Live Rescue. It's like stepping into last decade, but the stability is second to none.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Bare S100 CPU Replacement for ALTAIR 8800 IMSAI 8080 JAIR Single Board Computer picture

Bare S100 CPU Replacement for ALTAIR 8800 IMSAI 8080 JAIR Single Board Computer

$42.00



MITS Altair 8800 Computer Bamboo  Reproduction Arduino Tested Working Assembled  picture

MITS Altair 8800 Computer Bamboo Reproduction Arduino Tested Working Assembled

$649.99



MITS ALTAIR 8800  Original Vintage Microcomputer picture

MITS ALTAIR 8800 Original Vintage Microcomputer

$6000.00



Vintage SCCS Interface Microcomputer Magazine Pair 1976 IMSAI 8080 Altair 8800 picture

Vintage SCCS Interface Microcomputer Magazine Pair 1976 IMSAI 8080 Altair 8800

$26.00



Altair MITS 8800 CPU Parts Kit not IMSAI 8080 S100 (board NOT included) picture

Altair MITS 8800 CPU Parts Kit not IMSAI 8080 S100 (board NOT included)

$64.95



MITS ALTAIR 8800  Original Vintage Microcomputer  S-100   Buy It Now $5999 picture

MITS ALTAIR 8800 Original Vintage Microcomputer S-100 Buy It Now $5999

$5999.00



MITS ALTAIR 8800  Original Vintage Microcomputer with 14 boards - Buy It Now picture

MITS ALTAIR 8800 Original Vintage Microcomputer with 14 boards - Buy It Now

$9500.00



1974 Early Microcomputers by MITS Altair 8800's Ed Roberts HP-9810 Mark-8 Scelbi picture

1974 Early Microcomputers by MITS Altair 8800's Ed Roberts HP-9810 Mark-8 Scelbi

$55.00



Vintage Altair 8088 CPU Wire Wrapped S100 Card w Mon EPROM circuit board #T71 picture

Vintage Altair 8088 CPU Wire Wrapped S100 Card w Mon EPROM circuit board #T71

$99.00



VINTAGE DEC 1975 VOL 1 ISSUE 1 SCCS INTERFACE MAGAZINE MITS ALTAIR COVER & ADS picture

VINTAGE DEC 1975 VOL 1 ISSUE 1 SCCS INTERFACE MAGAZINE MITS ALTAIR COVER & ADS

$359.99